[ Upstream commit 0df12a01f4857495816b05f048c4c31439446e35 ]
We can currently sometimes get "RXS timed out" errors and "EOT timed out"
errors with spi transfers.
These errors can be made easy to reproduce by reading the cpcap iio
values in a loop while keeping the CPUs busy by also reading /dev/urandom.
The "RXS timed out" errors we can fix by adding spi-cpol and spi-cpha
in addition to the spi-cs-high property we already have.
The "EOT timed out" errors we can fix by increasing the spi clock rate
to 9.6 MHz. Looks similar MC13783 PMIC says it works at spi clock rates
up to 20 MHz, so let's assume we can pick any rate up to 20 MHz also
for cpcap.
Cc: maemo-leste@lists.dyne.org
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ac4e106d8934a5894811fc263f4b03fc8ed0fb7a ]
The FA2 mailbox is specified at 0x18025000 but should actually be
0x18025c00, length 0x400 according to socregs_nsp.h and board_bu.c. Also
the interrupt was off by one and should be GIC SPI 151 instead of 150.
Fixes: 17d517172300 ("ARM: dts: NSP: Add mailbox (PDC) to NSP")
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9cf28e41f9f768791f54ee18333239fda6927ed8 ]
While testing the recent suspend and resume regressions I noticed that
duovero can still end up losing edge gpio interrupts on runtime
suspend. This causes NFSroot easily stopping working after resume on
duovero.
Let's fix the issue by using gpio level interrupts for smsc as then
the gpio interrupt state is seen by the gpio controller on resume.
Fixes: 731b409878a3 ("ARM: dts: Configure duovero for to allow core retention during idle")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d7af722344e6dc52d87649100516515263e15c75 ]
AM3358 pin mcasp0_aclkr (ZCZ ball B13) [0] is routed to P1.31 header [1]
Mode 4 of this pin is mmc0_sdwp (SD Write Protect). A signal connected
to P1.31 may accidentally trigger mmc0 write protection. To avoid this
situation, do not put mcasp0_aclkr in mode 4 (mmc0_sdwp) by default.
[0] http://www.ti.com/lit/ds/symlink/am3358.pdf
[1] https://github.com/beagleboard/pocketbeagle/wiki/System-Reference-Manual#531_Expansion_Headers
Fixes: 047905376a16 (ARM: dts: Add am335x-pocketbeagle)
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Drew Fustini <drew@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 34b6826df7462c541752cf8b1de2691b26d78ae0 ]
The PWR-LED on the bananapi m2 zero board is on when gpio PL10 is low.
This has been verified on a board and in the schematics [1].
[1]: http://wiki.banana-pi.org/Banana_Pi_BPI-M2_ZERO#Documents
Fixes: 8b8061fcbfae ("ARM: dts: sun8i: h2+: add support for Banana Pi M2 Zero board")
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Cc: Icenowy Zheng <icenowy@aosc.io>
Cc: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb5cce12ac717c7462217cd493ed701d12d6dbce ]
The Arm Ltd. boards were using an outdated address convention in the DT
node names, by separating the high from the low 32-bits of an address by
a comma.
Remove the comma from the node name suffix to be DT spec compliant.
Link: https://lore.kernel.org/r/20200513103016.130417-3-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 869d42e6eba821905e1a0950623aadafe1a6e6d3 upstream.
SDHCI1 is connected to a BCM4329 WiFi/BT chip which requires
power to be kept over suspend. As the surrounding hardware supports
this, mark it as such. This fixes WiFi after a suspend/resume cycle.
Fixes: 170642468a51 ("ARM: dts: s5pv210: Add initial DTS for Samsung Aries based phones")
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit baa998aecb75c04d62be0a4ab6b724af6d73a0f9 upstream.
The gpio property for the vbus pin doesn't match the pinctrl and is
not correct.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Fixes: 42ed535595ec "ARM: dts: at91: introduce the sama5d2 ptc ek board"
Cc: stable@vger.kernel.org # 4.19 and later
Link: https://lore.kernel.org/r/20200401221947.41502-1-ludovic.desroches@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8807d356bfea92b0a8f04ce421800ed83400cd22 upstream.
GPIO lines for the CM36651 sensor I2C bus use the normal not the inverted
polarity. This bug has been there since adding the CM36651 sensor by
commit 85cb4e0bd229 ("ARM: dts: add cm36651 light/proximity sensor node
for exynos4412-trats2"), but went unnoticed because the "i2c-gpio"
driver ignored the GPIO polarity specified in the device-tree.
The recent conversion of "i2c-gpio" driver to the new, descriptor based
GPIO API, automatically made it the DT-specified polarity aware, what
broke the CM36651 sensor operation.
Fixes: 85cb4e0bd229 ("ARM: dts: add cm36651 light/proximity sensor node for exynos4412-trats2")
CC: stable@vger.kernel.org # 4.16+
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a1af7f36c70369b971ee1cf679dd68368dad23f0 upstream.
Remove non-removable and mmc-ddr-1_8v properties from the sdmmc0
node which come probably from an unchecked copy/paste.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Fixes:42ed535595ec "ARM: dts: at91: introduce the sama5d2 ptc ek board"
Cc: stable@vger.kernel.org # 4.19 and later
Link: https://lore.kernel.org/r/20200401221504.41196-1-ludovic.desroches@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit be0ec060b54f0481fb95d59086c1484a949c903c ]
These error messages are output when booting on a BCM HR2 system:
GIC: PPI11 is secure or misconfigured
GIC: PPI13 is secure or misconfigured
Per ARM documentation these interrupts are triggered on a rising edge.
See ARM Cortex A-9 MPCore Technical Reference Manual, Revision r4p1,
Section 3.3.8 Interrupt Configuration Registers.
The same issue was resolved for NSP systems in commit 5f1aa51c7a1e
("ARM: dts: NSP: Fix PPI interrupt types").
Fixes: b9099ec754b5 ("ARM: dts: Add Broadcom Hurricane 2 DTS include file")
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 58bb90ab415562eededb932455046924e65df342 ]
The status "ACT" led on the Raspberry Pi Zero W is on when GPIO 47 is low.
This has been verified on a board and somewhat confirmed by both the GPIO
name ("STATUS_LED_N") and the reduced schematics [1].
[1]: https://www.raspberrypi.org/documentation/hardware/raspberrypi/schematics/rpi_SCH_ZeroW_1p1_reduced.pdf
Fixes: 2c7c040c73e9 ("ARM: dts: bcm2835: Add Raspberry Pi Zero W")
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 665e7c73a7724a393b4ec92d1ae1e029925ef2b7 ]
Avoid LDB and IPU DI clocks both using the same parent. LDB requires
pasthrough clock to avoid breaking timing while IPU DI does not.
Force IPU DI clocks to use IMX6QDL_CLK_PLL2_PFD0_352M as parent
and LDB to use IMX6QDL_CLK_PLL5_VIDEO_DIV.
This fixes an issue where attempting atomic modeset while using
HDMI and display port at the same time causes LDB clock programming
to destroy the programming of HDMI that was done during the same
modeset.
Cc: stable@vger.kernel.org
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
[Use IMX6QDL_CLK_PLL2_PFD0_352M instead of IMX6QDL_CLK_PLL2_PFD2_396M
originally chosen by Robert Beckett to avoid affecting eMMC clock
by DRM atomic updates]
Signed-off-by: Ian Ray <ian.ray@ge.com>
[Squash Robert's and Ian's commits for bisectability, update patch
description and add stable tag]
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2c962369d72f286659e6446919f88d69b943cb4d ]
The size field of the tag header structure is supposed to be set to the
size of a tag structure including the header.
Fixes: c772568788b5f0 ("ARM: add additional table to compressed kernel")
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 855bdca1781c79eb661f89c8944c4a719ce720e8 ]
A test with the command below gives these errors:
arch/arm/boot/dts/rk3229-evb.dt.yaml: spi-0:
'#address-cells' is a required property
arch/arm/boot/dts/rk3229-evb.dt.yaml: spi-1:
'#address-cells' is a required property
arch/arm/boot/dts/rk3229-xms6.dt.yaml: spi-0:
'#address-cells' is a required property
arch/arm/boot/dts/rk3229-xms6.dt.yaml: spi-1:
'#address-cells' is a required property
The $nodename pattern for spi nodes is
"^spi(@.*|-[0-9a-f])*$". To prevent warnings rename
'spi-0' and 'spi-1' pinctrl sub nodenames to
'spi0' and 'spi1' in 'rk322x.dtsi'.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/spi/spi-controller.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200424123923.8192-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b14f3898d2c25a9b47a61fb879d0b1f3af92c59b ]
Dts files with Rockchip 'gpu' nodes were manually verified.
In order to automate this process arm,mali-utgard.txt
has been converted to yaml. In the new setup dtbs_check with
arm,mali-utgard.yaml expects clock-names values
in the same order, so fix that.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200425192500.1808-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 621c8d0c233e260232278a4cfd3380caa3c1da29 ]
A test with the command below gives for example this error:
arch/arm/boot/dts/rk3229-xms6.dt.yaml: phy@0:
'#phy-cells' is a required property
The phy nodename is normally used by a phy-handle.
This node is however compatible with
"ethernet-phy-id1234.d400", "ethernet-phy-ieee802.3-c22"
which is just been added to 'ethernet-phy.yaml'.
So change nodename to 'ethernet-phy' for which '#phy-cells'
is not a required property
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=~/.local/lib/python3.5/site-packages/dtschema/schemas/
phy/phy-provider.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20200416170321.4216-2-jbx6244@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 287e0d538fcec2f6e8eb1e565bf0749f3b90186d ]
A test with the command below gives for example this error:
arch/arm/boot/dts/rk3228-evb.dt.yaml: phy@0:
'#phy-cells' is a required property
The phy nodename is normally used by a phy-handle.
This node is however compatible with
"ethernet-phy-id1234.d400", "ethernet-phy-ieee802.3-c22"
which is just been added to 'ethernet-phy.yaml'.
So change nodename to 'ethernet-phy' for which '#phy-cells'
is not a required property
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=~/.local/lib/python3.5/site-packages/dtschema/schemas/
phy/phy-provider.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20200416170321.4216-1-jbx6244@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e47cb97f153193d4b41ca8d48127da14513d54c7 upstream.
The Clock Pulse Generator (CPG) device node lacks the extal2 clock.
This may lead to a failure registering the "r" clock, or to a wrong
parent for the "usb24s" clock, depending on MD_CK2 pin configuration and
boot loader CPG_USBCKCR register configuration.
This went unnoticed, as this does not affect the single upstream board
configuration, which relies on the first clock input only.
Fixes: d9ffd583bf345e2e ("ARM: shmobile: r8a7740: add SoC clocks to DTS")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Link: https://lore.kernel.org/r/20200508095918.6061-1-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0f739fdfe9e5ce668bd6d3210f310df282321837 upstream.
The R-Mobile APE6 Compare Match Timer 1 generates 8 interrupts, one for
each channel, but currently only 1 is described.
Fix this by adding the missing interrupts.
Fixes: f7b65230019b9dac ("ARM: shmobile: r8a73a4: Add CMT1 node")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200408090926.25201-1-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cbe63a8358310244e6007398bd2c7c70c7fd51cd upstream.
The Y Soft yapp4 platform supports up to two Ethernet ports.
The Ursa board though has only one Ethernet port populated and that is
the port@2. Since the introduction of this platform into mainline a wrong
port was deleted and the Ethernet could never work. Fix this by deleting
the correct port node.
Fixes: 87489ec3a77f ("ARM: dts: imx: Add Y Soft IOTA Draco, Hydra and Ursa boards")
Cc: stable@vger.kernel.org
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0caf34350a25907515d929a9c77b9b206aac6d1e upstream.
The I2C2 pins are already used and the following errors are seen:
imx27-pinctrl 10015000.iomuxc: pin MX27_PAD_I2C2_SDA already requested by 10012000.i2c; cannot claim for 1001d000.i2c
imx27-pinctrl 10015000.iomuxc: pin-69 (1001d000.i2c) status -22
imx27-pinctrl 10015000.iomuxc: could not request pin 69 (MX27_PAD_I2C2_SDA) from group i2c2grp on device 10015000.iomuxc
imx-i2c 1001d000.i2c: Error applying setting, reverse things back
imx-i2c: probe of 1001d000.i2c failed with error -22
Fix it by adding the correct I2C1 IOMUX entries for the pinctrl_i2c1 group.
Cc: <stable@vger.kernel.org>
Fixes: 61664d0b432a ("ARM: dts: imx27 phyCARD-S pinctrl")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 90d4d3f4ea45370d482fa609dbae4d2281b4074f upstream.
Even though commit cfb5d65f2595 ("ARM: dts: dra7: Add bus_dma_limit
for L3 bus") added bus_dma_limit for L3 bus, the PCIe controller
gets incorrect value of bus_dma_limit.
Fix it by adding empty dma-ranges property to axi@0 and axi@1
(parent device tree node of PCIe controller).
Cc: stable@kernel.org
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b7dc7205b2ae6b6c9d9cfc3e47d6f08da8647b10 upstream.
We need to indicate that powering off the TI WiFi is safe, to avoid:
wl18xx_driver wl18xx.2.auto: Unbalanced pm_runtime_enable!
wl1271_sdio mmc0:0001:2: wl12xx_sdio_power_on: failed to get_sync(-13)
which prevents the WiFi being functional.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Cc: Miguel Borges de Freitas <miguelborgesdefreitas@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 90444b958461a5f8fc299ece0fe17eab15cba1e1 upstream.
Since its inception the module was meant to be disabled by default, but
the original commit failed to add the relevant property.
Fixes: 4aba4cf82054 ("ARM: dts: bcm2835: Add the DSI module nodes and clocks")
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1a7e99599dffd836fcb720cdc0eaf3cd43d7af4a ]
A test with the command below gives this error:
arch/arm/boot/dts/rk3188-bqedison2qc.dt.yaml: lvds-encoder:
'ports' is a required property
Fix error by adding a ports wrapper for port@0 and port@1
inside the 'lvds-encoder' node for rk3188-bqedison2qc.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/display/
bridge/lvds-codec.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200316174647.5598-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9cd568dc588c5d168615bf34f325fabe33b2c9a0 ]
A test with the command below does not detect all errors
in combination with 'additionalProperties: false' and
allOf:
- $ref: "synopsys-dw-mshc-common.yaml#"
allOf:
- $ref: "mmc-controller.yaml#"
'additionalProperties' applies to all properties that are not
accounted-for by 'properties' or 'patternProperties' in
the immediate schema.
First when we combine rockchip-dw-mshc.yaml,
synopsys-dw-mshc-common.yaml and mmc-controller.yaml it gives
this error:
arch/arm/boot/dts/rk3188-bqedison2qc.dt.yaml: mmc@10218000:
'vmmcq-supply' does not match any of the regexes:
'^.*@[0-9]+$',
'^clk-phase-(legacy|sd-hs|mmc-(hs|hs[24]00|ddr52)|
uhs-(sdr(12|25|50|104)|ddr50))$',
'pinctrl-[0-9]+'
'vmmcq-supply' is not a valid property name for mmc nodes.
Fix this error by renaming it to 'vqmmc-supply'.
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200307134841.13803-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 4141f1a40fc0789f6fd4330e171e1edf155426aa upstream.
In order to wake from suspend by ethernet magic packets the GPC
must be used as intc does not have wakeup functionality.
But the FEC DT node currently uses interrupt-extended,
specificying intc, thus breaking WoL.
This problem is probably fallout from the stacked domain conversion
as intc used to chain to GPC.
So replace "interrupts-extended" by "interrupts" to use the default
parent which is GPC.
Fixes: b923ff6af0d5 ("ARM: imx6: convert GPC to stacked domains")
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7007f2eca0f258710899ca486da00546d03db0ed upstream.
USB_C_DET pin shouldn't be in ethernet group.
Creating a separate group allows one to use this pin
as an USB ID pin.
Fixes: b326629f25b7 ("ARM: dts: imx7: add Toradex Colibri iMX7S/iMX7D suppor")
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 32a1671ff8e84f0dfff3a50d4b2091d25e91f5e2 upstream.
Recent changes in the SPI core and the SPI-GPIO driver revealed that the
GPIO lines for the LD9040 LCD controller on the UniversalC210 board are
defined incorrectly. Fix the polarity for those lines to match the old
behavior and hardware requirements to fix LCD panel operation with
recent kernels.
Cc: <stable@vger.kernel.org> # 5.0.x
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b46b2b7ba6e104d265ab705914859ec0db7a98c5 ]
Commit cd28d1d6e52e ("net: phy: at803x: Disable phy delay for RGMII mode")
caused a regression for dm814x boards where NFSroot would no longer work.
Let's fix the issue by configuring "rgmii-id" mode as internal delays are
needed that is no longer the case with "rgmii" mode.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a40550952c000667b20082d58077bc647da6c890 ]
Lowering the voltage solves the quick image degradation over time
(minutes), that was probably caused by overheating.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Tony Lindgren