[ Upstream commit 8eddb3e7ce124dd6375d3664f1aae13873318b0f ]
If the VF virtual link is set to always enabled, the speed may be
unknown when the physical link is down. The driver currently logs
the link speed as 4294967295 Mbps which is SPEED_UNKNOWN. Modify
the link up log message as "speed unknown" which makes more sense.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/1602493854-29283-7-git-send-email-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8306266c1d51aac9aa7aa907fe99032a58c6382c ]
The fr_hard_header function is used to prepend the header to skbs before
transmission. It is used in 3 situations:
1) When a control packet is generated internally in this driver;
2) When a user sends an skb on an Ethernet-emulating PVC device;
3) When a user sends an skb on a normal PVC device.
These 3 situations need to be handled differently by fr_hard_header.
Different headers should be prepended to the skb in different situations.
Currently fr_hard_header distinguishes these 3 situations using
skb->protocol. For situation 1 and 2, a special skb->protocol value
will be assigned before calling fr_hard_header, so that it can recognize
these 2 situations. All skb->protocol values other than these special ones
are treated by fr_hard_header as situation 3.
However, it is possible that in situation 3, the user sends an skb with
one of the special skb->protocol values. In this case, fr_hard_header
would incorrectly treat it as situation 1 or 2.
This patch tries to solve this issue by using skb->dev instead of
skb->protocol to distinguish between these 3 situations. For situation
1, skb->dev would be NULL; for situation 2, skb->dev->type would be
ARPHRD_ETHER; and for situation 3, skb->dev->type would be ARPHRD_DLCI.
This way fr_hard_header would be able to distinguish these 3 situations
correctly regardless what skb->protocol value the user tries to use in
situation 3.
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 99f41b8e43b8b4b31262adb8ac3e69088fff1289 ]
When STBC is enabled, NSTS_SU value need to be accounted for VHT NSS
calculation for SU case.
Without this fix, 1SS + STBC enabled case was reported wrongly as 2SS
in radiotap header on monitor mode capture.
Tested-on: QCA9984 10.4-3.10-00047
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597392971-3897-1-git-send-email-murugana@codeaurora.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2fd3c8f34d08af0a6236085f9961866ad92ef9ec ]
When simulate random transfer fail for sdio write and read, it happened
"payload length exceeds max htc length" and recovery later sometimes.
Test steps:
1. Add config and update kernel:
CONFIG_FAIL_MMC_REQUEST=y
CONFIG_FAULT_INJECTION=y
CONFIG_FAULT_INJECTION_DEBUG_FS=y
2. Run simulate fail:
cd /sys/kernel/debug/mmc1/fail_mmc_request
echo 10 > probability
echo 10 > times # repeat until hitting issues
3. It happened payload length exceeds max htc length.
[ 199.935506] ath10k_sdio mmc1:0001:1: payload length 57005 exceeds max htc length: 4088
....
[ 264.990191] ath10k_sdio mmc1:0001:1: payload length 57005 exceeds max htc length: 4088
4. after some time, such as 60 seconds, it start recovery which triggered
by wmi command timeout for periodic scan.
[ 269.229232] ieee80211 phy0: Hardware restart was requested
[ 269.734693] ath10k_sdio mmc1:0001:1: device successfully recovered
The simulate fail of sdio is not a real sdio transter fail, it only
set an error status in mmc_should_fail_request after the transfer end,
actually the transfer is success, then sdio_io_rw_ext_helper will
return error status and stop transfer the left data. For example,
the really RX len is 286 bytes, then it will split to 2 blocks in
sdio_io_rw_ext_helper, one is 256 bytes, left is 30 bytes, if the
first 256 bytes get an error status by mmc_should_fail_request,then
the left 30 bytes will not read in this RX operation. Then when the
next RX arrive, the left 30 bytes will be considered as the header
of the read, the top 4 bytes of the 30 bytes will be considered as
lookaheads, but actually the 4 bytes is not the lookaheads, so the len
from this lookaheads is not correct, it exceeds max htc length 4088
sometimes. When happened exceeds, the buffer chain is not matched between
firmware and ath10k, then it need to start recovery ASAP. Recently then
recovery will be started by wmi command timeout, but it will be long time
later, for example, it is 60+ seconds later from the periodic scan, if
it does not have periodic scan, it will be longer.
Start recovery when it happened "payload length exceeds max htc length"
will be reasonable.
This patch only effect sdio chips.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00029.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200108031957.22308-3-wgong@codeaurora.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0daf2bf5a2dcf33d446b76360908f109816e2e21 ]
Each EMAD transaction stores the skb used to issue the EMAD request
('trans->tx_skb') so that the request could be retried in case of a
timeout. The skb can be freed when a corresponding response is received
or as part of the retry logic (e.g., failed retransmit, exceeded maximum
number of retries).
The two tasks (i.e., response processing and retransmits) are
synchronized by the atomic 'trans->active' field which ensures that
responses to inactive transactions are ignored.
In case of a failed retransmit the transaction is finished and all of
its resources are freed. However, the current code does not mark it as
inactive. Syzkaller was able to hit a race condition in which a
concurrent response is processed while the transaction's resources are
being freed, resulting in a use-after-free [1].
Fix the issue by making sure to mark the transaction as inactive after a
failed retransmit and free its resources only if a concurrent task did
not already do that.
[1]
BUG: KASAN: use-after-free in consume_skb+0x30/0x370
net/core/skbuff.c:833
Read of size 4 at addr ffff88804f570494 by task syz-executor.0/1004
CPU: 0 PID: 1004 Comm: syz-executor.0 Not tainted 5.8.0-rc7+ #68
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS
rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xf6/0x16e lib/dump_stack.c:118
print_address_description.constprop.0+0x1c/0x250
mm/kasan/report.c:383
__kasan_report mm/kasan/report.c:513 [inline]
kasan_report.cold+0x1f/0x37 mm/kasan/report.c:530
check_memory_region_inline mm/kasan/generic.c:186 [inline]
check_memory_region+0x14e/0x1b0 mm/kasan/generic.c:192
instrument_atomic_read include/linux/instrumented.h:56 [inline]
atomic_read include/asm-generic/atomic-instrumented.h:27 [inline]
refcount_read include/linux/refcount.h:147 [inline]
skb_unref include/linux/skbuff.h:1044 [inline]
consume_skb+0x30/0x370 net/core/skbuff.c:833
mlxsw_emad_trans_finish+0x64/0x1c0 drivers/net/ethernet/mellanox/mlxsw/core.c:592
mlxsw_emad_process_response drivers/net/ethernet/mellanox/mlxsw/core.c:651 [inline]
mlxsw_emad_rx_listener_func+0x5c9/0xac0 drivers/net/ethernet/mellanox/mlxsw/core.c:672
mlxsw_core_skb_receive+0x4df/0x770 drivers/net/ethernet/mellanox/mlxsw/core.c:2063
mlxsw_pci_cqe_rdq_handle drivers/net/ethernet/mellanox/mlxsw/pci.c:595 [inline]
mlxsw_pci_cq_tasklet+0x12a6/0x2520 drivers/net/ethernet/mellanox/mlxsw/pci.c:651
tasklet_action_common.isra.0+0x13f/0x3e0 kernel/softirq.c:550
__do_softirq+0x223/0x964 kernel/softirq.c:292
asm_call_on_stack+0x12/0x20 arch/x86/entry/entry_64.S:711
Allocated by task 1006:
save_stack+0x1b/0x40 mm/kasan/common.c:48
set_track mm/kasan/common.c:56 [inline]
__kasan_kmalloc mm/kasan/common.c:494 [inline]
__kasan_kmalloc.constprop.0+0xc2/0xd0 mm/kasan/common.c:467
slab_post_alloc_hook mm/slab.h:586 [inline]
slab_alloc_node mm/slub.c:2824 [inline]
slab_alloc mm/slub.c:2832 [inline]
kmem_cache_alloc+0xcd/0x2e0 mm/slub.c:2837
__build_skb+0x21/0x60 net/core/skbuff.c:311
__netdev_alloc_skb+0x1e2/0x360 net/core/skbuff.c:464
netdev_alloc_skb include/linux/skbuff.h:2810 [inline]
mlxsw_emad_alloc drivers/net/ethernet/mellanox/mlxsw/core.c:756 [inline]
mlxsw_emad_reg_access drivers/net/ethernet/mellanox/mlxsw/core.c:787 [inline]
mlxsw_core_reg_access_emad+0x1ab/0x1420 drivers/net/ethernet/mellanox/mlxsw/core.c:1817
mlxsw_reg_trans_query+0x39/0x50 drivers/net/ethernet/mellanox/mlxsw/core.c:1831
mlxsw_sp_sb_pm_occ_clear drivers/net/ethernet/mellanox/mlxsw/spectrum_buffers.c:260 [inline]
mlxsw_sp_sb_occ_max_clear+0xbff/0x10a0 drivers/net/ethernet/mellanox/mlxsw/spectrum_buffers.c:1365
mlxsw_devlink_sb_occ_max_clear+0x76/0xb0 drivers/net/ethernet/mellanox/mlxsw/core.c:1037
devlink_nl_cmd_sb_occ_max_clear_doit+0x1ec/0x280 net/core/devlink.c:1765
genl_family_rcv_msg_doit net/netlink/genetlink.c:669 [inline]
genl_family_rcv_msg net/netlink/genetlink.c:714 [inline]
genl_rcv_msg+0x617/0x980 net/netlink/genetlink.c:731
netlink_rcv_skb+0x152/0x440 net/netlink/af_netlink.c:2470
genl_rcv+0x24/0x40 net/netlink/genetlink.c:742
netlink_unicast_kernel net/netlink/af_netlink.c:1304 [inline]
netlink_unicast+0x53a/0x750 net/netlink/af_netlink.c:1330
netlink_sendmsg+0x850/0xd90 net/netlink/af_netlink.c:1919
sock_sendmsg_nosec net/socket.c:651 [inline]
sock_sendmsg+0x150/0x190 net/socket.c:671
____sys_sendmsg+0x6d8/0x840 net/socket.c:2359
___sys_sendmsg+0xff/0x170 net/socket.c:2413
__sys_sendmsg+0xe5/0x1b0 net/socket.c:2446
do_syscall_64+0x56/0xa0 arch/x86/entry/common.c:384
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Freed by task 73:
save_stack+0x1b/0x40 mm/kasan/common.c:48
set_track mm/kasan/common.c:56 [inline]
kasan_set_free_info mm/kasan/common.c:316 [inline]
__kasan_slab_free+0x12c/0x170 mm/kasan/common.c:455
slab_free_hook mm/slub.c:1474 [inline]
slab_free_freelist_hook mm/slub.c:1507 [inline]
slab_free mm/slub.c:3072 [inline]
kmem_cache_free+0xbe/0x380 mm/slub.c:3088
kfree_skbmem net/core/skbuff.c:622 [inline]
kfree_skbmem+0xef/0x1b0 net/core/skbuff.c:616
__kfree_skb net/core/skbuff.c:679 [inline]
consume_skb net/core/skbuff.c:837 [inline]
consume_skb+0xe1/0x370 net/core/skbuff.c:831
mlxsw_emad_trans_finish+0x64/0x1c0 drivers/net/ethernet/mellanox/mlxsw/core.c:592
mlxsw_emad_transmit_retry.isra.0+0x9d/0xc0 drivers/net/ethernet/mellanox/mlxsw/core.c:613
mlxsw_emad_trans_timeout_work+0x43/0x50 drivers/net/ethernet/mellanox/mlxsw/core.c:625
process_one_work+0xa3e/0x17a0 kernel/workqueue.c:2269
worker_thread+0x9e/0x1050 kernel/workqueue.c:2415
kthread+0x355/0x470 kernel/kthread.c:291
ret_from_fork+0x22/0x30 arch/x86/entry/entry_64.S:293
The buggy address belongs to the object at ffff88804f5703c0
which belongs to the cache skbuff_head_cache of size 224
The buggy address is located 212 bytes inside of
224-byte region [ffff88804f5703c0, ffff88804f5704a0)
The buggy address belongs to the page:
page:ffffea00013d5c00 refcount:1 mapcount:0 mapping:0000000000000000
index:0x0
flags: 0x100000000000200(slab)
raw: 0100000000000200 dead000000000100 dead000000000122 ffff88806c625400
raw: 0000000000000000 00000000000c000c 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff88804f570380: fc fc fc fc fc fc fc fc fb fb fb fb fb fb fb fb
ffff88804f570400: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>ffff88804f570480: fb fb fb fb fc fc fc fc fc fc fc fc fc fc fc fc
^
ffff88804f570500: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffff88804f570580: 00 00 00 00 00 00 00 00 00 00 00 00 fc fc fc fc
Fixes: caf7297e7ab5f ("mlxsw: core: Introduce support for asynchronous EMAD register access")
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 23025393dbeb3b8b3b60ebfa724cdae384992e27 upstream.
In order to reduce the chance for the system becoming unresponsive due
to event storms triggered by a misbehaving netfront use the lateeoi
irq binding for netback and unmask the event channel only just before
going to sleep waiting for new events.
Make sure not to issue an EOI when none is pending by introducing an
eoi_pending element to struct xenvif_queue.
When no request has been consumed set the spurious flag when sending
the EOI for an interrupt.
This is part of XSA-332.
Cc: stable@vger.kernel.org
Reported-by: Julien Grall <julien@xen.org>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Wei Liu <wl@xen.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 478762855b5ae9f68fa6ead1edf7abada70fcd5f upstream.
In p54p_tx(), skb->data is mapped to streaming DMA on line 337:
mapping = pci_map_single(..., skb->data, ...);
Then skb->data is accessed on line 349:
desc->device_addr = ((struct p54_hdr *)skb->data)->req_id;
This access may cause data inconsistency between CPU cache and hardware.
To fix this problem, ((struct p54_hdr *)skb->data)->req_id is stored in
a local variable before DMA mapping, and then the driver accesses this
local variable instead of skb->data.
Cc: <stable@vger.kernel.org>
Signed-off-by: Jia-Ju Bai <baijiaju@tsinghua.edu.cn>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200802132949.26788-1-baijiaju@tsinghua.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 631ce27a3006fc0b732bfd589c6df505f62eadd9 ]
As part of the commit b148bb238c02
("bnxt_en: Fix possible crash in bnxt_fw_reset_task()."),
cancel_delayed_work_sync() is called only for VFs to fix a possible
crash by cancelling any pending delayed work items. It was assumed
by mistake that the flush_workqueue() call on the PF would flush
delayed work items as well.
As flush_workqueue() does not cancel the delayed workqueue, extend
the fix for PFs. This fix will avoid the system crash, if there are
any pending delayed work items in fw_reset_task() during driver's
.remove() call.
Unify the workqueue cleanup logic for both PF and VF by calling
cancel_work_sync() and cancel_delayed_work_sync() directly in
bnxt_remove_one().
Fixes: b148bb238c02 ("bnxt_en: Fix possible crash in bnxt_fw_reset_task().")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 21d6a11e2cadfb8446265a3efff0e2aad206e15e ]
A recent patch has moved the workqueue cleanup logic before
calling unregister_netdev() in bnxt_remove_one(). This caused a
regression because the workqueue can be restarted if the device is
still open. Workqueue cleanup must be done after unregister_netdev().
The workqueue will not restart itself after the device is closed.
Call bnxt_cancel_sp_work() after unregister_netdev() and
call bnxt_dl_fw_reporters_destroy() after that. This fixes the
regession and the original NULL ptr dereference issue.
Fixes: b16939b59cc0 ("bnxt_en: Fix NULL ptr dereference crash in bnxt_fw_reset_task()")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f75d9a0aa96721d20011cd5f8c7a24eb32728589 ]
When a PCIe fatal error occurs, the internal latched BAR addresses
in the chip get reset even though the BAR register values in config
space are retained.
pci_restore_state() will not rewrite the BAR addresses if the
BAR address values are valid, causing the chip's internal BAR addresses
to stay invalid. So we need to zero the BAR registers during PCIe fatal
error to force pci_restore_state() to restore the BAR addresses. These
write cycles to the BAR registers will cause the proper BAR addresses to
latch internally.
Fixes: 6316ea6db93d ("bnxt_en: Enable AER support.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 68b9f0865b1ef545da180c57d54b82c94cb464a4 ]
In the function ravb_hwtstamp_get() in ravb_main.c with the existing
values for RAVB_RXTSTAMP_TYPE_V2_L2_EVENT (0x2) and RAVB_RXTSTAMP_TYPE_ALL
(0x6)
if (priv->tstamp_rx_ctrl & RAVB_RXTSTAMP_TYPE_V2_L2_EVENT)
config.rx_filter = HWTSTAMP_FILTER_PTP_V2_L2_EVENT;
else if (priv->tstamp_rx_ctrl & RAVB_RXTSTAMP_TYPE_ALL)
config.rx_filter = HWTSTAMP_FILTER_ALL;
if the test on RAVB_RXTSTAMP_TYPE_ALL should be true,
it will never be reached.
This issue can be verified with 'hwtstamp_config' testing program
(tools/testing/selftests/net/hwtstamp_config.c). Setting filter type
to ALL and subsequent retrieving it gives incorrect value:
$ hwtstamp_config eth0 OFF ALL
flags = 0
tx_type = OFF
rx_filter = ALL
$ hwtstamp_config eth0
flags = 0
tx_type = OFF
rx_filter = PTP_V2_L2_EVENT
Correct this by converting if-else's to switch.
Fixes: c156633f1353 ("Renesas Ethernet AVB driver proper")
Reported-by: Julia Lawall <julia.lawall@inria.fr>
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Link: https://lore.kernel.org/r/20201026102130.29368-1-andrew_gabbasov@mentor.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2734a24e6e5d18522fbf599135c59b82ec9b2c9e ]
As reported by Serge flag IRQF_NO_THREAD causes an error if the
interrupt is actually shared and the other driver(s) don't have this
flag set. This situation can occur if a PCI(e) legacy interrupt is
used in combination with forced threading.
There's no good way to deal with this properly, therefore we have to
remove flag IRQF_NO_THREAD. For fixing the original forced threading
issue switch to napi_schedule().
Fixes: 424a646e072a ("r8169: fix operation under forced interrupt threading")
Link: https://www.spinics.net/lists/netdev/msg694960.html
Reported-by: Serge Belyshev <belyshev@depni.sinp.msu.ru>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Serge Belyshev <belyshev@depni.sinp.msu.ru>
Link: https://lore.kernel.org/r/b5b53bfe-35ac-3768-85bf-74d1290cf394@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8fc3672a8ad3e782bac80e979bc2a2c10960cbe9 ]
Jakub Kicinski brought up a concern in ibmvnic_set_mac().
ibmvnic_set_mac() does this:
ether_addr_copy(adapter->mac_addr, addr->sa_data);
if (adapter->state != VNIC_PROBED)
rc = __ibmvnic_set_mac(netdev, addr->sa_data);
So if state == VNIC_PROBED, the user can assign an invalid address to
adapter->mac_addr, and ibmvnic_set_mac() will still return 0.
The fix is to validate ethernet address at the beginning of
ibmvnic_set_mac(), and move the ether_addr_copy to
the case of "adapter->state != VNIC_PROBED".
Fixes: c26eba03e407 ("ibmvnic: Update reset infrastructure to support tunable parameters")
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Link: https://lore.kernel.org/r/20201027220456.71450-1-ljp@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 937d8420588421eaa5c7aa5c79b26b42abb288ef ]
The current code sets up the filter action field before
rewrites are set up. When the action 'switch' is used
with rewrites, this may result in initial few packets
that get switched out don't have rewrites applied
on them.
So, make sure filter action is set up along with rewrites
or only after everything else is set up for rewrites.
Fixes: 12b276fbf6e0 ("cxgb4: add support to create hash filters")
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Link: https://lore.kernel.org/r/20201023115852.18262-1-rajur@chelsio.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 825741b071722f1c8ad692cead562c4b5f5eaa93 ]
In the AER or firmware reset flow, if we are in fatal error state or
if pci_channel_offline() is true, we don't send any commands to the
firmware because the commands will likely not reach the firmware and
most commands don't matter much because the firmware is likely to be
reset imminently.
However, the HWRM_FUNC_RESET command is different and we should always
attempt to send it. In the AER flow for example, the .slot_reset()
call will trigger this fw command and we need to try to send it to
effect the proper reset.
Fixes: b340dc680ed4 ("bnxt_en: Avoid sending firmware messages when AER error is detected.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bad60b8d1a7194df38fd7fe4b22f3f4dcf775099 ]
The idx in __ath10k_htt_rx_ring_fill_n function lives in
consistent dma region writable by the device. Malfunctional
or malicious device could manipulate such idx to have a OOB
write. Either by
htt->rx_ring.netbufs_ring[idx] = skb;
or by
ath10k_htt_set_paddrs_ring(htt, paddr, idx);
The idx can also be negative as it's signed, giving a large
memory space to write to.
It's possibly exploitable by corruptting a legit pointer with
a skb pointer. And then fill skb with payload as rougue object.
Part of the log here. Sometimes it appears as UAF when writing
to a freed memory by chance.
[ 15.594376] BUG: unable to handle page fault for address: ffff887f5c1804f0
[ 15.595483] #PF: supervisor write access in kernel mode
[ 15.596250] #PF: error_code(0x0002) - not-present page
[ 15.597013] PGD 0 P4D 0
[ 15.597395] Oops: 0002 [#1] SMP KASAN PTI
[ 15.597967] CPU: 0 PID: 82 Comm: kworker/u2:2 Not tainted 5.6.0 #69
[ 15.598843] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996),
BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014
[ 15.600438] Workqueue: ath10k_wq ath10k_core_register_work [ath10k_core]
[ 15.601389] RIP: 0010:__ath10k_htt_rx_ring_fill_n
(linux/drivers/net/wireless/ath/ath10k/htt_rx.c:173) ath10k_core
Signed-off-by: Zekun Shen <bruceshenzk@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200623221105.3486-1-bruceshenzk@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6c151410d5b57e6bb0d91a735ac511459539a7bf ]
When brcmf_proto_msgbuf_attach fail and msgbuf->txflow_wq != NULL,
we should destroy the workqueue.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1595237765-66238-1-git-send-email-wangyufen@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 621a3a8b1c0ecf16e1e5667ea5756a76a082b738 ]
syzbot is reporting that del_timer_sync() is called from
mwifiex_usb_cleanup_tx_aggr() from mwifiex_unregister_dev() without
checking timer_setup() from mwifiex_usb_tx_init() was called [1].
Ganapathi Bhat proposed a possibly cleaner fix, but it seems that
that fix was forgotten [2].
"grep -FrB1 'del_timer' drivers/ | grep -FA1 '.function)'" says that
currently there are 28 locations which call del_timer[_sync]() only if
that timer's function field was initialized (because timer_setup() sets
that timer's function field). Therefore, let's use same approach here.
[1] https://syzkaller.appspot.com/bug?id=26525f643f454dd7be0078423e3cdb0d57744959
[2] https://lkml.kernel.org/r/CA+ASDXMHt2gq9Hy+iP_BYkWXsSreWdp3_bAfMkNcuqJ3K+-jbQ@mail.gmail.com
Reported-by: syzbot <syzbot+dc4127f950da51639216@syzkaller.appspotmail.com>
Cc: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Cc: Brian Norris <briannorris@chromium.org>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Acked-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200821082720.7716-1-penguin-kernel@I-love.SAKURA.ne.jp
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 86279456a4d47782398d3cb8193f78f672e36cac ]
Free the skb if usb_submit_urb fails on rx_urb. And free the urb
no matter usb_submit_urb succeeds or not in rtl8xxxu_submit_int_urb.
Signed-off-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200906040424.22022-1-chiu@endlessm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f4443293d741d1776b86ed1dd8c4e4285d0775fc ]
When wlc_phy_txpwr_srom_read_lcnphy fails in wlc_phy_attach_lcnphy,
the allocated pi->u.pi_lcnphy is leaked, since struct brcms_phy will be
freed in the caller function.
Fix this by calling wlc_phy_detach_lcnphy in the error handler of
wlc_phy_txpwr_srom_read_lcnphy before returning.
Signed-off-by: Keita Suzuki <keitasuzuki.park@sslab.ics.keio.ac.jp>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200908121743.23108-1-keitasuzuki.park@sslab.ics.keio.ac.jp
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03fb92a432ea5abe5909bca1455b7e44a9380480 ]
Calls to usb_kill_anchored_urbs() after usb_kill_urb() on multiprocessor
systems create a race condition in which usb_kill_anchored_urbs() deallocates
the URB before the completer callback is called in usb_kill_urb(), resulting
in a use-after-free.
To fix this, add proper lock protection to usb_kill_urb() calls that can
possibly run concurrently with usb_kill_anchored_urbs().
Reported-by: syzbot+89bd486af9427a9fc605@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?id=cabffad18eb74197f84871802fd2c5117b61febf
Signed-off-by: Brooke Basile <brookebasile@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200911071427.32354-1-brookebasile@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ad02c7f4f279504bdd38ab706fdc97d5f2b2a9c ]
This patch implements error handling and propagates the error value of
flexcan_chip_stop(). This function will be called from flexcan_suspend()
in an upcoming patch in some SoCs which support LPSR mode.
Add a new function flexcan_chip_stop_disable_on_error() that tries to
disable the chip even in case of errors.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
[mkl: introduce flexcan_chip_stop_disable_on_error() and use it in flexcan_close()]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20200922144429.2613631-11-mkl@pengutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee755732b7a16af018daa77d9562d2493fb7092f ]
The vht capability of MAX_MPDU_LENGTH is 11454 in rtw88; however, the rx
buffer size for each packet is 8192. When receiving packets that are
larger than rx buffer size, it will leads to rx buffer ring overflow.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200925061219.23754-2-tehuang@realtek.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3af5f0f5c74ecbaf757ef06c3f80d56751277637 ]
kmalloc returns KSEG0 addresses so convert back from KSEG1
in kfree. Also make sure array is freed when the driver is
unloaded from the kernel.
Fixes: ef11291bcd5f ("Add support the Korina (IDT RC32434) Ethernet MAC")
Signed-off-by: Valentin Vidic <vvidic@valentin-vidic.from.hr>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 53708f4fd9cfe389beab5c8daa763bcd0e0b4aef ]
clang static analysis reports this problem:
sdio.c:2403:3: warning: Attempt to free released memory
kfree(card->mpa_rx.buf);
^~~~~~~~~~~~~~~~~~~~~~~
When mwifiex_init_sdio() fails in its first call to
mwifiex_alloc_sdio_mpa_buffer, it falls back to calling it
again. If the second alloc of mpa_tx.buf fails, the error
handler will try to free the old, previously freed mpa_rx.buf.
Reviewing the code, it looks like a second double free would
happen with mwifiex_cleanup_sdio().
So set both pointers to NULL when they are freed.
Fixes: 5e6e3a92b9a4 ("wireless: mwifiex: initial commit for Marvell mwifiex driver")
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201004131931.29782-1-trix@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 903b3f9badf1d54f77b468b96706dab679b45b14 ]
A print in the remain on channel code was too long and caused
a WARNING, split it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fixes: dc28e12f2125 ("iwlwifi: mvm: ROC: Extend the ROC max delay duration & limit ROC duration")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200930102759.58d57c0bdc68.Ib06008665e7bf1199c360aa92691d9c74fb84990@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a53b59ece86c86d16d12ccdaa1ad0c78250a9d96 ]
enic_dev_wait() has a BUG_ON(in_interrupt()).
Chasing the callers of enic_dev_wait() revealed the gems of enic_reset()
and enic_tx_hang_reset() which are both invoked through work queues in
order to be able to call rtnl_lock(). So far so good.
After locking rtnl both functions acquire enic::enic_api_lock which
serializes against the (ab)use from infiniband. This is where the
trainwreck starts.
enic::enic_api_lock is a spin_lock() which implicitly disables preemption,
but both functions invoke a ton of functions under that lock which can
sleep. The BUG_ON(in_interrupt()) does not trigger in that case because it
can't detect the preempt disabled condition.
This clearly has never been tested with any of the mandatory debug options
for 7+ years, which would have caught that for sure.
Cure it by adding a enic_api_busy member to struct enic, which is modified
and evaluated with enic::enic_api_lock held.
If enic_api_devcmd_proxy_by_index() observes enic::enic_api_busy as true,
it drops enic::enic_api_lock and busy waits for enic::enic_api_busy to
become false.
It would be smarter to wait for a completion of that busy period, but
enic_api_devcmd_proxy_by_index() is called with other spin locks held which
obviously can't sleep.
Remove the BUG_ON(in_interrupt()) check as well because it's incomplete and
with proper debugging enabled the problem would have been caught from the
debug checks in schedule_timeout().
Fixes: 0b038566c0ea ("drivers/net: enic: Add an interface for USNIC to interact with firmware")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 63f6982075d890d7563e2469643f05a37d193f01 ]
Currently if an unsupported iftype is detected the error return path
does not free the cmd_skb leading to a resource leak. Fix this by
free'ing cmd_skb.
Addresses-Coverity: ("Resource leak")
Fixes: 805b28c05c8e ("qtnfmac: prepare for AP_VLAN interface type support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200925132224.21638-1-colin.king@canonical.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b9cd795b0e4860f482bf3741d12e1c8f3ec1cfc9 ]
Set up the speed according to crq->query_phys_parms.rsp.speed.
Fix IBMVNIC_10GBPS typo.
Fixes: f8d6ae0d27ec ("ibmvnic: Report actual backing device speed and duplex values")
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6a950755cec1a90ddaaff3e4acb5333617441c32 ]
The "tsid" is a user controlled u8 which comes from debugfs. Values
more than 15 are invalid because "active_tsids" is a 16 bit variable.
If the value of "tsid" is more than 31 then that leads to a shift
wrapping bug.
Fixes: 8fffd9e5ec9e ("ath6kl: Implement support for QOS-enable and QOS-disable from userspace")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200918142732.GA909725@mwanda
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a7920efdd86d8a0d74402dbc80ead03b023294ba ]
There is an off-by-one error in rtl8366rb_is_vlan_valid()
making VLANs 0..4094 valid while it should be 1..4095.
Fix it.
Fixes: d8652956cf37 ("net: dsa: realtek-smi: Add Realtek SMI driver")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3dfe8dde093a07e82fa472c0f8c29a7f6a2006a5 ]
We go to lengths to determine whether the PVID should be set
for this port or not, and then fail to take it into account.
Fix this oversight.
Fixes: d8652956cf37 ("net: dsa: realtek-smi: Add Realtek SMI driver")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7e1301ed1881447d2a25f9c6423738c33cbca133 ]
The VLANs and PVIDs on the RTL8366 utilizes a "member
configuration" (MC) which is largely unexplained in the
code.
This set-up requires a special ordering: rtl8366_set_pvid()
must be called first, followed by rtl8366_set_vlan(),
else the MC will not be properly allocated. Relax this
by factoring out the code obtaining an MC and reuse
the helper in both rtl8366_set_pvid() and
rtl8366_set_vlan() so we remove this strict ordering
requirement.
In the process, add some better comments and debug prints
so people who read the code understand what is going on.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6641a2c42b0a307b7638d10e5d4b90debc61389d ]
The rtl8366_set_vlan() and rtl8366_set_pvid() get invalid
VLANs tossed at it, especially VLAN0, something the hardware
and driver cannot handle. Check validity and bail out like
we do in the other callbacks.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9f19306d166688a73356aa636c62e698bf2063cc ]
The current implementation of stmmac_stop_all_queues() and
stmmac_start_all_queues() will not work correctly when the value of
tx_queues_to_use is changed through ethtool -L DEVNAME rx N tx M command.
Also, netif_tx_start|stop_all_queues() are only needed in driver open()
and close() only.
Fixes: c22a3f48 net: stmmac: adding multiple napi mechanism
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d2ffdc8d4002a62de31ff7aa3bef28c843c3cbe ]
Before calling timecounter_cyc2time(), clock->lock must be taken.
Use mlx5_timecounter_cyc2time instead which guarantees a safe access.
Fixes: afc98a0b46d8 ("net/mlx5: Update ptp_clock_event foreach PPS event")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d2ab7f00f4321370a8ee14e5630d4349fdacc42e ]
A possible call chain is as follow:
mwifiex_sdio_interrupt (sdio.c)
--> mwifiex_main_process (main.c)
--> mwifiex_process_cmdresp (cmdevt.c)
--> mwifiex_process_sta_cmdresp (sta_cmdresp.c)
--> mwifiex_ret_802_11_scan (scan.c)
--> mwifiex_parse_single_response_buf (scan.c)
'mwifiex_sdio_interrupt()' is an interrupt function.
Also note that 'mwifiex_ret_802_11_scan()' already uses GFP_ATOMIC.
So use GFP_ATOMIC instead of GFP_KERNEL when memory is allocated in
'mwifiex_parse_single_response_buf()'.
Fixes: 7c6fa2a843c5 ("mwifiex: use cfg80211 dynamic scan table and cfg80211_get_bss API")
or
Fixes: 601216e12c65e ("mwifiex: process RX packets in SDIO IRQ thread directly")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200809092906.744621-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c9f015bc9f8839831c7ba0a6d731a3853c464e2 ]
Clang static analysis reports this error
brcmfmac/core.c:490:4: warning: Dereference of null pointer
(*ifp)->ndev->stats.rx_errors++;
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In this block of code
if (ret || !(*ifp) || !(*ifp)->ndev) {
if (ret != -ENODATA && *ifp)
(*ifp)->ndev->stats.rx_errors++;
brcmu_pkt_buf_free_skb(skb);
return -ENODATA;
}
(*ifp)->ndev being NULL is caught as an error
But then it is used to report the error.
So add a check before using it.
Fixes: 91b632803ee4 ("brcmfmac: Use net_device_stats from struct net_device")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200802161804.6126-1-trix@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3b9fb6791e7113679b1eb472e6ce1659e80f5797 ]
Qualcomm's document "80-WL007-1 Rev. J" states that the highest rx rate for
the WCN3660 and WCN3680 on MCS 7 is 150 Mbps not the 72 Mbps stated here.
This patch fixes the data-rate declared in the 5GHz table.
Fixes: 8e84c2582169 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680
hardware")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200802004824.1307124-1-bryan.odonoghue@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 454530a9950b5a26d4998908249564cedfc4babc ]
Update the size used in 'dma_free_coherent()' in order to match the one
used in the corresponding 'dma_alloc_coherent()'.
Fixes: 1863008369ae ("ath10k: fix shadow register implementation for WCN3990")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200802122227.678637-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2705cd7558e718a7240c64eb0afb2edad5f8c190 ]
The value of "htc_hdr->endpoint_id" comes from skb->data so Smatch marks
it as untrusted so we have to check it before using it as an array
offset.
This is similar to a bug that syzkaller found in commit e4ff08a4d727
("ath9k: Fix use-after-free Write in ath9k_htc_rx_msg") so it is
probably a real issue.
Fixes: fb9987d0f748 ("ath9k_htc: Support for AR9271 chipset.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200813141253.GA457408@mwanda
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 54f9ab7b870934b70e5a21786d951fbcf663970f ]
The value for "aid" comes from skb->data so Smatch marks it as
untrusted. If it's invalid then it can result in an out of bounds array
access in ath6kl_add_new_sta().
Fixes: 572e27c00c9d ("ath6kl: Fix AP mode connect event parsing and TIM updates")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200813141315.GB457408@mwanda
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 720e5c03e5cb26d33d97f55192b791bb48478aa5 ]
It is expected that the returned counters by .get_survey are monotonic
increasing. But the data from ath10k gets reset to zero regularly. Channel
active/busy time are then showing incorrect values (less than previous or
sometimes zero) for the currently active channel during successive survey
dump commands.
example:
$ iw dev wlan0 survey dump
Survey data from wlan0
frequency: 5180 MHz [in use]
channel active time: 54995 ms
channel busy time: 432 ms
channel receive time: 0 ms
channel transmit time: 59 ms
...
$ iw dev wlan0 survey dump
Survey data from wlan0
frequency: 5180 MHz [in use]
channel active time: 32592 ms
channel busy time: 254 ms
channel receive time: 0 ms
channel transmit time: 0 ms
...
The correct way to handle this is to use the non-clearing
WMI_BSS_SURVEY_REQ_TYPE_READ wmi_bss_survey_req_type. The firmware will
then accumulate the survey data and handle wrap arounds.
Tested-on: QCA9984 hw1.0 10.4-3.5.3-00057
Tested-on: QCA988X hw2.0 10.2.4-1.0-00047
Tested-on: QCA9888 hw2.0 10.4-3.9.0.2-00024
Tested-on: QCA4019 hw1.0 10.4-3.6-00140
Fixes: fa7937e3d5c2 ("ath10k: update bss channel survey information")
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Tested-by: Markus Theil <markus.theil@tu-ilmenau.de>
Tested-by: John Deere <24601deerej@gmail.com>
[sven@narfation.org: adjust commit message]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1592232686-28712-1-git-send-email-kvalo@codeaurora.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
Michael Chan