bnxt failed to check the exist of xdp_set_data_meta_invalid() and
makes meta_data uninited in xdp_buff.
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Uninitialized xdp->data_meta can result in NULL pointer deference in
bpf_xdp_adjust_head(). Therefore, fix it by init it with
xdp_set_data_meta_invalid().
Signed-off-by: Menglong Dong <imagedong@tencent.com>
[ Upstream commit 6d72e7c767acbbdd44ebc7d89c6690b405b32b57 ]
In emac_mac_tx_buf_send, it calls emac_tx_fill_tpd(..,skb,..).
If some error happens in emac_tx_fill_tpd(), the skb will be freed via
dev_kfree_skb(skb) in error branch of emac_tx_fill_tpd().
But the freed skb is still used via skb->len by netdev_sent_queue(,skb->len).
As i observed that emac_tx_fill_tpd() haven't modified the value of skb->len,
thus my patch assigns skb->len to 'len' before the possible free and
use 'len' instead of skb->len later.
Fixes: b9b17debc69d2 ("net: emac: emac gigabit ethernet controller driver")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5718458b092bf6bf4482c5df32affba3c3259517 ]
When a lot of frames were received in the short term, the driver
caused a stuck of receiving until a new frame was received. For example,
the following command from other device could cause this issue.
$ sudo ping -f -l 1000 -c 1000 <this driver's ipaddress>
The previous code always cleared the interrupt flag of RX but checks
the interrupt flags in ravb_poll(). So, ravb_poll() could not call
ravb_rx() in the next time until a new RX frame was received if
ravb_rx() returned true. To fix the issue, always calls ravb_rx()
regardless the interrupt flags condition.
Fixes: c156633f1353 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d83b8aa5207d81f9f6daec9888390f079cc5db3f ]
The bit-masks used for the TXERRCH and RXERRCH (tx and rx error channels)
are incorrect and always lead to a zero result. The mask values are
currently the incorrect post-right shifted values, fix this by setting
them to the currect values.
(I double checked these against the TMS320TCI6482 data sheet, section
5.30, page 127 to ensure I had the correct mask values for the TXERRCH
and RXERRCH fields in the MACSTATUS register).
Addresses-Coverity: ("Operands don't affect result")
Fixes: a6286ee630f6 ("net: Add TI DaVinci EMAC driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e701a25840360706fe4cf5de0015913ca19c274b ]
The shifting of the u8 integers rq->caching by 26 bits to
the left will be promoted to a 32 bit signed int and then
sign-extended to a u64. In the event that rq->caching is
greater than 0x1f then all then all the upper 32 bits of
the u64 end up as also being set because of the int
sign-extension. Fix this by casting the u8 values to a
u64 before the 26 bit left shift.
Addresses-Coverity: ("Unintended sign extension")
Fixes: 4863dea3fab0 ("net: Adding support for Cavium ThunderX network controller")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dd2c79677375c37f8f9f8d663eb4708495d595ef ]
The shifting of the u8 integers f->fs.nat_lip[] by 24 bits to
the left will be promoted to a 32 bit signed int and then
sign-extended to a u64. In the event that the top bit of the u8
is set then all then all the upper 32 bits of the u64 end up as
also being set because of the sign-extension. Fix this by
casting the u8 values to a u64 before the 24 bit left shift.
Addresses-Coverity: ("Unintended sign extension")
Fixes: 12b276fbf6e0 ("cxgb4: add support to create hash filters")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 298b58f00c0f86868ea717426beb5c1198772f81 ]
The macro CN23XX_PEM_BAR1_INDEX_REG is being used to shift oct->pcie_port
(a u16) left 24 places. There are two subtle issues here, first the
shift gets promoted to an signed int and then sign extended to a u64.
If oct->pcie_port is 0x80 or more then the upper bits get sign extended
to 1. Secondly shfiting a u16 24 bits will lead to an overflow so it
needs to be cast to a u64 for all the bits to not overflow.
It is entirely possible that the u16 port value is never large enough
for this to fail, but it is useful to fix unintended overflows such
as this.
Fix this by casting the port parameter to the macro to a u64 before
the shift.
Addresses-Coverity: ("Unintended sign extension")
Fixes: 5bc67f587ba7 ("liquidio: CN23XX register definitions")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d392ecd1bc29ae15b0e284d5f732c2d36f244271 ]
Limiting the scope of the variable vector_ring_chain to the block where it
is used.
Fixes: 424eb834a9be ("net: hns3: Unified HNS3 {VF|PF} Ethernet Driver for hip08 SoC")
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit cbaf3f6af9c268caf558c8e7ec52bcb35c5455dd upstream.
Each multicast route that is forwarding packets (as opposed to trapping
them) points to a list of egress router interfaces (RIFs) through which
packets are replicated.
A route's action can transition from trap to forward when a RIF is
created for one of the route's egress virtual interfaces (eVIF). When
this happens, the route's action is first updated and only later the
list of egress RIFs is committed to the device.
This results in the route pointing to an invalid list. In case the list
pointer is out of range (due to uninitialized memory), the device will
complain:
mlxsw_spectrum2 0000:06:00.0: EMAD reg access failed (tid=5733bf490000905c,reg_id=300f(pefa),type=write,status=7(bad parameter))
Fix this by first committing the list of egress RIFs to the device and
only later update the route's action.
Note that a fix is not needed in the reverse function (i.e.,
mlxsw_sp_mr_route_evif_unresolve()), as there the route's action is
first updated and only later the RIF is removed from the list.
Cc: stable@vger.kernel.org
Fixes: c011ec1bbfd6 ("mlxsw: spectrum: Add the multicast routing offloading logic")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Link: https://lore.kernel.org/r/20210506072308.3834303-1-idosch@idosch.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6e6026f2dd2005844fb35c3911e8083c09952c6c upstream.
The Intel I211 Ethernet Controller supports 2 Receive Side Scaling (RSS)
queues. It should not be excluded from having this feature enabled.
Via commit c883de9fd787 ("igb: rename igb define to be more generic")
E1000_MRQC_ENABLE_RSS_4Q was renamed to E1000_MRQC_ENABLE_RSS_MQ to
indicate that this is a generic bit flag to enable queues and not
a flag that is specific to devices that support 4 queues
The bit flag enables 2, 4 or 8 queues appropriately depending on the part.
Tested with a multicore CPU and frames were then distributed as expected.
This issue appears to have been introduced because of confusion caused
by the prior name.
Signed-off-by: Nick Lowe <nick.lowe@gmail.com>
Tested-by: David Switzer <david.switzer@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 416dcc5ce9d2a810477171c62ffa061a98f87367 ]
Fix the following coccicheck warning:
./drivers/net/ethernet/cavium/liquidio/cn66xx_regs.h:413:6-28:
duplicated argument to & or |
The CN6XXX_INTR_M1UPB0_ERR here is duplicate.
Here should be CN6XXX_INTR_M1UNB0_ERR.
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 453a77894efa4d9b6ef9644d74b9419c47ac427c ]
It has been reported [0] that using pause frames in jumbo mode impacts
performance. There's no available chip documentation, but vendor
drivers r8168 and r8125 don't advertise pause in jumbo mode. So let's
do the same, according to Roman it fixes the issue.
[0] https://bugzilla.kernel.org/show_bug.cgi?id=212617
Fixes: 9cf9b84cc701 ("r8169: make use of phy_set_asym_pause")
Reported-by: Roman Mamedov <rm+bko@romanrm.net>
Tested-by: Roman Mamedov <rm+bko@romanrm.net>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5e00e16cb98935bcf06f51931876d898c226f65c ]
So far we don't increase the max read request size if we switch to
jumbo mode before bringing up the interface for the first time.
Let's change this.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9db0ac57bd3286fedcf43a86b29b847cea281cc7 ]
Merge enabling and disabling jumbo packets to one function to make
the code a little simpler.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 21b5f672fb2eb1366dedc4ac9d32431146b378d3 ]
It turned out that on low performance systems the original change can
cause lower tx performance. On a N3450-based mini-PC tx performance
in iperf3 was reduced from 950Mbps to ~900Mbps. Therefore effectively
revert the original change, just use pcie_set_readrq() now instead of
changing the PCIe capability register directly.
Fixes: 2df49d365498 ("r8169: remove fiddling with the PCIe max read request size")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e0bbe7cbb3c5ff72d680993edf89db2391e80d5d ]
r8168b_0_hw_jumbo_enable() and r8168b_0_hw_jumbo_disable() both do the
same and just set PCI_EXP_DEVCTL_NOSNOOP_EN. We can simplify the code
by moving this setting for RTL8168B to rtl_hw_start_8168().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2df49d36549808a7357ad9f78b7a8e39516e7809 ]
The attempt to improve performance by changing the PCIe max read request
size was added in the vendor driver more than 10 years back and copied
to r8169 driver. In the vendor driver this has been removed long ago.
Obviously it had no effect, also in my tests I didn't see any
difference. Typically the max payload size is less than 512 bytes
anyway, and the PCI core takes care that the maximum supported value
is set. So let's remove fiddling with PCIe max read request size from
r8169 too.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 7c451f3ef676c805a4b77a743a01a5c21a250a73 upstream.
Remove the unnecessary napi_schedule() call in __ibmvnic_open() since
interrupt_rx() calls napi_schedule_prep/__napi_schedule during every
receive interrupt.
Fixes: ed651a10875f ("ibmvnic: Updated reset handling")
Signed-off-by: Lijun Pan <lijunp213@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d3a6abccbd272aea7dc2c6f984bb5a2c11278e44 upstream.
During adapter reset, do_reset/do_hard_reset calls ibmvnic_open(),
which will calls napi_schedule if previous state is VNIC_CLOSED
(i.e, the reset case, and "ifconfig down" case). So there is no need
for do_reset to call napi_schedule again at the end of the function
though napi_schedule will neglect the request if napi is already
scheduled.
Fixes: ed651a10875f ("ibmvnic: Updated reset handling")
Signed-off-by: Lijun Pan <lijunp213@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0775ebc4cf8554bdcd2c212669a0868ab68df5c0 upstream.
__ibmvnic_open calls napi_disable without checking whether NAPI polling
has already been disabled or not. This could cause napi_disable
being called twice, which could generate deadlock. For example,
the first napi_disable will spin until NAPI_STATE_SCHED is cleared
by napi_complete_done, then set it again.
When napi_disable is called the second time, it will loop infinitely
because no dev->poll will be running to clear NAPI_STATE_SCHED.
To prevent above scenario from happening, call ibmvnic_napi_disable()
which checks if napi is disabled or not before calling napi_disable.
Fixes: bfc32f297337 ("ibmvnic: Move resource initialization to its own routine")
Suggested-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: Lijun Pan <lijunp213@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 31457db3750c0b0ed229d836f2609fdb8a5b790e upstream.
When the probe fails, we must disable the regulator that was previously
enabled.
This patch is a follow-up to commit ac88c531a5b3
("net: davicom: Fix regulator not turned off on failed probe") which missed
one case.
Fixes: 7994fe55a4a2 ("dm9000: Add regulator and reset support to dm9000")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a714e27ea8bdee2b238748029d31472d0a65b611 upstream.
Commit a14d273ba159 ("net: macb: restore cmp registers on resume path")
introduces the restore of CMP registers on resume path. In case the IP
doesn't support type 2 screeners (zero on DCFG8 register) the
struct macb::rx_fs_list::list is not initialized and thus the
list_for_each_entry(item, &bp->rx_fs_list.list, list) loop introduced in
commit a14d273ba159 ("net: macb: restore cmp registers on resume path")
will access an uninitialized list leading to crash. Thus, initialize
the struct macb::rx_fs_list::list without taking into account if the
IP supports type 2 screeners or not.
Fixes: a14d273ba159 ("net: macb: restore cmp registers on resume path")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 66c3f05ddc538ee796321210c906b6ae6fc0792a ]
pci_resource_start() is not a good indicator to determine if a PCI
resource exists or not, since the resource may start at address 0.
This is seen when trying to instantiate the driver in qemu for riscv32
or riscv64.
pci 0000:00:01.0: reg 0x10: [io 0x0000-0x001f]
pci 0000:00:01.0: reg 0x14: [mem 0x00000000-0x0000001f]
...
pcnet32: card has no PCI IO resources, aborting
Use pci_resouce_len() instead.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ed7bedd2c3ca040f1e8ea02c6590a93116b1ec78 ]
Currently, the VF down state bit is cleared after VF sending
link status request command. There is problem that when VF gets
link status replied from PF, the down state bit may still set
as 1. In this case, the link status replied from PF will be
ignored and always set VF link status to down.
To fix this problem, clear VF down state bit before VF requests
link status.
Fixes: e2cb1dec9779 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a7b76002ae78cd230ee652ccdfedf21aa94fcecc ]
Calculating the number of compeltion EQs based on the number of
available IRQ vectors doesn't work now that all async EQs share one IRQ.
Thus the max number of EQs can be exceeded on systems with more than
approximately 256 CPUs. Take this into account when calculating the
number of available completion EQs.
Fixes: 81bfa206032a ("net/mlx5: Use a single IRQ for all async EQs")
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3211434dfe7a66fcf55e43961ea524b78336c04c ]
Use connector_type read from PTYS register when it's valid, based on
corresponding capability bit.
Fixes: 5b4793f81745 ("net/mlx5e: Add support for reading connector type from PTYS")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Eran Ben Elisha <eranbe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2ea538dbee1c79f6f6c24a6f2f82986e4b7ccb78 ]
A merge hint message needs some time to process before the merged
flow actually reaches the firmware, during which we may get duplicate
merge hints if there're more than one packet that hit the pre-merged
flow. And processing duplicate merge hints will cost extra host_ctx's
which are a limited resource.
Avoid the duplicate merge by using hash table to store the sub_flows
to be merged.
Fixes: 8af56f40e53b ("nfp: flower: offload merge flows")
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1bfb3dea965ff9f6226fd1709338f227363b6061 ]
Accessing SGE_QBASE_MAP[0-3] and SGE_QBASE_INDEX registers can lead
to SGE missing doorbells under heavy traffic. So, only collect them
when adapter is idle. Also update the regdump range to skip collecting
these registers.
Fixes: 80a95a80d358 ("cxgb4: collect SGE PF/VF queue map")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bff5b62585123823842833ab20b1c0a7fa437f8c ]
Handle return error code of eth_mac_addr();
Fixes: 3d23a05c75c7 ("gianfar: Enable changing mac addr when if up")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d75135082698140a26a56defe1bbc1b06f26a41f ]
Based on the IOMMU configuration, the current cache control settings can
result in possible coherency issues. The hardware team has recommended
new settings for the PCI device path to eliminate the issue.
Fixes: 6f595959c095 ("amd-xgbe: Adjust register settings to improve performance")
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6e5a03bcba44e080a6bf300194a68ce9bb1e5184 upstream.
In nfp_bpf_ctrl_msg_rx, if
nfp_ccm_get_type(skb) == NFP_CCM_TYPE_BPF_BPF_EVENT is true, the skb
will be freed. But the skb is still used by nfp_ccm_rx(&bpf->ccm, skb).
My patch adds a return when the skb was freed.
Fixes: bcf0cafab44fd ("nfp: split out common control message handling code")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b7eeb52721fe417730fc5adc5cbeeb5fe349ab26 upstream.
When ice_remove_vsi_lkup_fltr is called, by calling
ice_add_to_vsi_fltr_list local copy of vsi filter list
is created. If any issues during creation of vsi filter
list occurs it up for the caller to free already
allocated memory. This patch ensures proper memory
deallocation in these cases.
Fixes: 80d144c9ac82 ("ice: Refactor switch rule management structures and functions")
Signed-off-by: Robert Malz <robertx.malz@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7a91d3f02b04b2fb18c2dfa8b6c4e5a40a2753f5 upstream.
Add handling of allocation fault for ice_vsi_list_map_info.
Also *fi should not be NULL pointer, it is a reference to raw
data field, so remove this variable and use the reference
directly.
Fixes: 9daf8208dd4d ("ice: Add support for switch filter programming")
Signed-off-by: Jacek Bułatek <jacekx.bulatek@intel.com>
Co-developed-by: Haiyue Wang <haiyue.wang@intel.com>
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f88c529ac77b3c21819d2cf1dfcfae1937849743 upstream.
250 msec timeout is insufficient for some AQ commands. Advice from FW
team was to increase the timeout. Increase to 1 second.
Fixes: 7ec59eeac804 ("ice: Add support for control queues")
Signed-off-by: Fabio Pricoco <fabio.pricoco@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0571a753cb07982cc82f4a5115e0b321da89e1f3 ]
pxa168_eth_remove() firstly calls unregister_netdev(),
then cancels a timeout work. unregister_netdev() shuts down a device
interface and removes it from the kernel tables. If the timeout occurs
in parallel, the timeout work (pxa168_eth_tx_timeout_task) performs stop
and open of the device. It may lead to an inconsistent state and memory
leaks.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Pavel Andrianov <andrianov@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a28af7a3e85ddf358f8c41e401a33002f7a9587 ]
The aq_nic_start function can fail in a variety of cases which leaves
the device in broken state.
An example case where the start function fails is the
request_threaded_irq which can be interrupted, resulting in a EINTR
result. This can be manually triggered by bringing the link up (e.g. ip
link set up) and triggering a SIGINT on the initiating process (e.g.
Ctrl+C). This would put the device into a half configured state.
Subsequently bringing the link up again would cause the napi_enable to
BUG.
In order to correctly clean up the failed attempt to start a device call
aq_nic_stop.
Signed-off-by: Nathan Rossi <nathan.rossi@digi.com>
Reviewed-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7867299cde34e9c2d2c676f2a384a9d5853b914d ]
The condition should be skipped if CPU ID equal to nthreads.
The patch doesn't fix any actual issue since
nthreads = min_t(unsigned int, num_present_cpus(), MVPP2_MAX_THREADS).
On all current Armada platforms, the number of CPU's is
less than MVPP2_MAX_THREADS.
Fixes: e531f76757eb ("net: mvpp2: handle cases where more CPUs are available than s/w threads")
Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 014dfa26ce1c647af09bf506285ef67e0e3f0a6b ]
MTU cannot be changed on dwmac-sun8i. (ip link set eth0 mtu xxx returning EINVAL)
This is due to tx_fifo_size being 0, since this value is used to compute valid
MTU range.
Like dwmac-sunxi (with commit 806fd188ce2a ("net: stmmac: dwmac-sunxi: Provide TX and RX fifo sizes"))
dwmac-sun8i need to have tx and rx fifo sizes set.
I have used values from datasheets.
After this patch, setting a non-default MTU (like 1000) value works and network is still useable.
Tested-on: sun8i-h3-orangepi-pc
Tested-on: sun8i-r40-bananapi-m2-ultra
Tested-on: sun50i-a64-bananapi-m64
Tested-on: sun50i-h5-nanopi-neo-plus2
Tested-on: sun50i-h6-pine-h64
Fixes: 9f93ac8d408 ("net-next: stmmac: Add dwmac-sun8i")
Reported-by: Belisko Marek <marek.belisko@gmail.com>
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 64451b98306bf1334a62bcd020ec92bdb4cb68db ]
unmapping npc counter works in a way by traversing all mcam
entries to find which mcam rule is associated with counter.
But loop cursor variable 'entry' is not incremented before
checking next mcam entry which resulting in infinite loop.
This in turn hogs the kworker thread forever and no other
mbox message is processed by AF driver after that.
Fix this by updating entry value before checking next
mcam entry.
Fixes: a958dd59f9ce ("octeontx2-af: Map or unmap NPC MCAM entry and counter")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ae2619dd4fccdad9876aa5f900bd85484179c50f ]
Current devlink code try to free already freed irqs as the
irq_allocate flag is not cleared after free leading to kernel
crash while removing rvu driver. The patch fixes the irq free
sequence and clears the irq_allocate flag on free.
Fixes: 7304ac4567bc ("octeontx2-af: Add mailbox IRQ and msg handlers")
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d8ce0275e45ec809a33f98fc080fe7921b720dfb ]
pre_tun_rule flows does not follow the usual add-flow path, instead
they are used to update the pre_tun table on the firmware. This means
that if the mask-id gets allocated here the firmware will never see the
"NFP_FL_META_FLAG_MANAGE_MASK" flag for the specific mask id, which
triggers the allocation on the firmware side. This leads to the firmware
mask being corrupted and causing all sorts of strange behaviour.
Fixes: f12725d98cbe ("nfp: flower: offload pre-tunnel rules")
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6897087323a2fde46df32917462750c069668b2f ]
The interrupt handler may set the flag to reset the mac in the future,
but that flag is not cleared once the reset has occurred.
Fixes: 10cbd6407609 ("ftgmac100: Rework NAPI & interrupts handling")
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit db74623a3850db99cb9692fda9e836a56b74198d ]
In qlcnic_83xx_get_minidump_template, fw_dump->tmpl_hdr was freed by
vfree(). But unfortunately, it is used when extended is true.
Fixes: 7061b2bdd620e ("qlogic: Deletion of unnecessary checks before two function calls")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b52912b8293f2c496f42583e65599aee606a0c18 ]
There is one e1e_wphy() call in e1000_set_d0_lplu_state_82571
that we have caught its return value but lack further handling.
Check and terminate the execution flow just like other e1e_wphy()
in this function.
Fixes: bc7f75fa9788 ("[E1000E]: New pci-express e1000 driver (currently for ICH9 devices only)")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 21f857f0321d0d0ea9b1a758bd55dc63d1cb2437 ]
A possible race condition was found in e1000_reset_task,
after discovering a similar issue in igb driver via
commit 024a8168b749 ("igb: reinit_locked() should be called
with rtnl_lock").
Added rtnl_lock() and rtnl_unlock() to avoid this.
Fixes: bc7f75fa9788 ("[E1000E]: New pci-express e1000 driver (currently for ICH9 devices only)")
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Menglong Dong