commit 1fe976d308acb6374c899a4ee8025a0a016e453e upstream.
Since commit fee2d546414d ("net: phy: marvell: mv88e6390 temperature
sensor reading"), Linux reports the temperature of Topaz hwmon as
constant -75°C.
This is because switches from the Topaz family (88E6141 / 88E6341) have
the address of the temperature sensor register different from Peridot.
This address is instead compatible with 88E1510 PHYs, as was used for
Topaz before the above mentioned commit.
Create a new mapping table between switch family and PHY ID for families
which don't have a model number. And define PHY IDs for Topaz and Peridot
families.
Create a new PHY ID and a new PHY driver for Topaz's internal PHY.
The only difference from Peridot's PHY driver is the HWMON probing
method.
Prior this change Topaz's internal PHY is detected by kernel as:
PHY [...] driver [Marvell 88E6390] (irq=63)
And afterwards as:
PHY [...] driver [Marvell 88E6341 Family] (irq=63)
Signed-off-by: Pali Rohár <pali@kernel.org>
BugLink: https://github.com/globalscaletechnologies/linux/issues/1
Fixes: fee2d546414d ("net: phy: marvell: mv88e6390 temperature sensor reading")
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4b5923249b8fa427943b50b8f35265176472be38 upstream.
There are a few more bits in the GSWIP_MII_CFG register for which we
did rely on the boot-loader (or the hardware defaults) to set them up
properly.
For some external RMII PHYs we need to select the GSWIP_MII_CFG_RMII_CLK
bit and also we should un-set it for non-RMII PHYs. The
GSWIP_MII_CFG_RMII_CLK bit is ignored for other PHY connection modes.
The GSWIP IP also supports in-band auto-negotiation for RGMII PHYs when
the GSWIP_MII_CFG_RGMII_IBS bit is set. Clear this bit always as there's
no known hardware which uses this (so it is not tested yet).
Clear the xMII isolation bit when set at initialization time if it was
previously set by the bootloader. Not doing so could lead to no traffic
(neither RX nor TX) on a port with this bit set.
While here, also add the GSWIP_MII_CFG_RESET bit. We don't need to
manage it because this bit is self-clearning when set. We still add it
here to get a better overview of the GSWIP_MII_CFG register.
Fixes: 14fceff4771e51 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Cc: stable@vger.kernel.org
Suggested-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Updated after the upstream commit 3e9005be87777 required some changes
for Linux 5.4 ]
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3e9005be87777afc902b9f5497495898202d335d upstream.
PHY auto polling on the GSWIP hardware can be used so link changes
(speed, link up/down, etc.) can be detected automatically. Internally
GSWIP reads the PHY's registers for this functionality. Based on this
automatic detection GSWIP can also automatically re-configure it's port
settings. Unfortunately this auto polling (and configuration) mechanism
seems to cause various issues observed by different people on different
devices:
- FritzBox 7360v2: the two Gbit/s ports (connected to the two internal
PHY11G instances) are working fine but the two Fast Ethernet ports
(using an AR8030 RMII PHY) are completely dead (neither RX nor TX are
received). It turns out that the AR8030 PHY sets the BMSR_ESTATEN bit
as well as the ESTATUS_1000_TFULL and ESTATUS_1000_XFULL bits. This
makes the PHY auto polling state machine (rightfully?) think that the
established link speed (when the other side is Gbit/s capable) is
1Gbit/s.
- None of the Ethernet ports on the Zyxel P-2812HNU-F1 (two are
connected to the internal PHY11G GPHYs while the other three are
external RGMII PHYs) are working. Neither RX nor TX traffic was
observed. It is not clear which part of the PHY auto polling state-
machine caused this.
- FritzBox 7412 (only one LAN port which is connected to one of the
internal GPHYs running in PHY22F / Fast Ethernet mode) was seeing
random disconnects (link down events could be seen). Sometimes all
traffic would stop after such disconnect. It is not clear which part
of the PHY auto polling state-machine cauased this.
- TP-Link TD-W9980 (two ports are connected to the internal GPHYs
running in PHY11G / Gbit/s mode, the other two are external RGMII
PHYs) was affected by similar issues as the FritzBox 7412 just without
the "link down" events
Switch to software based configuration instead of PHY auto polling (and
letting the GSWIP hardware configure the ports automatically) for the
following link parameters:
- link up/down
- link speed
- full/half duplex
- flow control (RX / TX pause)
After a big round of manual testing by various people (who helped test
this on OpenWrt) it turns out that this fixes all reported issues.
Additionally it can be considered more future proof because any
"quirk" which is implemented for a PHY on the driver side can now be
used with the GSWIP hardware as well because Linux is in control of the
link parameters.
As a nice side-effect this also solves a problem where fixed-links were
not supported previously because we were relying on the PHY auto polling
mechanism, which cannot work for fixed-links as there's no PHY from
where it can read the registers. Configuring the link settings on the
GSWIP ports means that we now use the settings from device-tree also for
ports with fixed-links.
Fixes: 14fceff4771e51 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Fixes: 3e6fdeb28f4c33 ("net: dsa: lantiq_gswip: Let GSWIP automatically set the xMII clock")
Cc: stable@vger.kernel.org
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Move gswip_port_set_{speed, duplex, pause} calls from
gswip_phylink_mac_link_up to gswip_phylink_mac_config because the
data required for these functions is not available inside
gswip_phylink_mac_link_up yet in Linux 5.4 (it was only added with
Linux 5.7). ]
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3e6fdeb28f4c331acbd27bdb0effc4befd4ef8e8 upstream.
The xMII interface clock depends on the PHY interface (MII, RMII, RGMII)
as well as the current link speed. Explicitly configure the GSWIP to
automatically select the appropriate xMII interface clock.
This fixes an issue seen by some users where ports using an external
RMII or RGMII PHY were deaf (no RX or TX traffic could be seen). Most
likely this is due to an "invalid" xMII clock being selected either by
the bootloader or hardware-defaults.
Fixes: 14fceff4771e51 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d45c36bafb94e72fdb6dee437279b61b6d97e706 upstream.
The bcm_sf2 driver uses the b53 driver as a library but does not make
usre of the b53_setup() function, this made it fail to inherit the
vlan_filtering_is_global attribute. Fix this by moving the assignment to
b53_switch_alloc() which is used by bcm_sf2.
Fixes: 7228b23e68f7 ("net: dsa: b53: Let DSA handle mismatched VLAN filtering settings")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 47142ed6c34d544ae9f0463e58d482289cbe0d46 ]
Similar to commit 92696286f3bb37ba50e4bd8d1beb24afb759a799 ("net:
bcmgenet: Set phydev->dev_flags only for internal PHYs") we need to
qualify the phydev->dev_flags based on whether the port is connected to
an internal or external PHY otherwise we risk having a flags collision
with a completely different interpretation depending on the driver.
Fixes: aa9aef77c761 ("net: dsa: bcm_sf2: communicate integrated PHY revision to PHY driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f9b3827ee66cfcf297d0acd6ecf33653a5f297ef upstream.
Add support for being able to set the learning attribute on port, and
make sure that the standalone ports start up with learning disabled.
We can remove the code in bcm_sf2 that configured the ports learning
attribute because we want the standalone ports to have learning disabled
by default and port 7 cannot be bridged, so its learning attribute will
not change past its initial configuration.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f72f2fb8fb6be095b98af5d740ac50cffd0b0cae upstream.
Having multiple destination ports for a unicast address does not make
sense.
Make port_db_load_purge override existent unicast portvec instead of
adding a new port bit.
Fixes: 884729399260 ("net: dsa: mv88e6xxx: handle multiple ports in ATU")
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20210130134334.10243-1-dqfext@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8e4052c32d6b4b39c1e13c652c7e33748d447409 upstream.
The > comparison should be >= to prevent accessing one element beyond
the end of the dev->vlans[] array in the caller function, b53_vlan_add().
The "dev->vlans" array is allocated in the b53_switch_init() function
and it has "dev->num_vlans" elements.
Fixes: a2482d2ce349 ("net: dsa: b53: Plug in VLAN support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/YAbxI97Dl/pmBy5V@mwanda
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 87fe04367d842c4d97a77303242d4dd4ac351e46 upstream.
mv88e6xxx_port_vlan_join checks whether the VTU already contains an
entry for the given vid (via mv88e6xxx_vtu_getnext), and if so, merely
changes the relevant .member[] element and loads the updated entry
into the VTU.
However, at least for the mv88e6250, the on-stack struct
mv88e6xxx_vtu_entry vlan never has its .state[] array explicitly
initialized, neither in mv88e6xxx_port_vlan_join() nor inside the
getnext implementation. So the new entry has random garbage for the
STU bits, breaking VLAN filtering.
When the VTU entry is initially created, those bits are all zero, and
we should make sure to keep them that way when the entry is updated.
Fixes: 92307069a96c (net: dsa: mv88e6xxx: Avoid VTU corruption on 6097)
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Tobias Waldekranz <tobias@waldekranz.com>
Tested-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 709a3c9dff2a639966ae7d8ba6239d2b8aba036d ]
There is one GSWIP_MII_CFG register for each switch-port except the CPU
port. The register offset for the first port is 0x0, 0x02 for the
second, 0x04 for the third and so on.
Update the driver to not only restrict the GSWIP_MII_CFG registers to
ports 0, 1 and 5. Handle ports 0..5 instead but skip the CPU port. This
means we are not overwriting the configuration for the third port (port
two since we start counting from zero) with the settings for the sixth
port (with number five) anymore.
The GSWIP_MII_PCDU(p) registers are not updated because there's really
only three (one for each of the following ports: 0, 1, 5).
Fixes: 14fceff4771e51 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c1a9ec7e5d577a9391660800c806c53287fca991 ]
Enable GSWIP_MII_CFG_EN also for internal PHYs to make traffic flow.
Without this the PHY link is detected properly and ethtool statistics
for TX are increasing but there's no RX traffic coming in.
Fixes: 14fceff4771e51 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Suggested-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a3dcb3e7e70c72a68a79b30fc3a3adad5612731c ]
When the switch is hardware reset, it reads the contents of the
EEPROM. This can contain instructions for programming values into
registers and to perform waits between such programming. Reading the
EEPROM can take longer than the 100ms mv88e6xxx_hardware_reset() waits
after deasserting the reset GPIO. So poll the EEPROM done bit to
ensure it is complete.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ruslan Sushko <rus@sushko.dev>
Link: https://lore.kernel.org/r/20201116164301.977661-1-rus@sushko.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2a1828e378c1b5ba1ff283ed8f8c5cc37bb391dc ]
A user reports (slightly shortened from the original message):
libphy: lantiq,xrx200-mdio: probed
mdio_bus 1e108000.switch-mii: MDIO device at address 17 is missing.
gswip 1e108000.switch lan: no phy at 2
gswip 1e108000.switch lan: failed to connect to port 2: -19
lantiq,xrx200-net 1e10b308.eth eth0: error -19 setting up slave phy
This is a single-port board using the internal Fast Ethernet PHY. The
user reports that switching to PHY scanning instead of configuring the
PHY within device-tree works around this issue.
The documentation for the standalone variant of the PHY11G (which is
probably very similar to what is used inside the xRX200 SoCs but having
the firmware burnt onto that standalone chip in the factory) states that
the PHY needs 300ms to be ready for MDIO communication after releasing
the reset.
Add a 300ms delay after initializing all GPHYs to ensure that the GPHY
firmware had enough time to initialize and to appear on the MDIO bus.
Unfortunately there is no (known) documentation on what the minimum time
to wait after releasing the reset on an internal PHY so play safe and
take the one for the external variant. Only wait after the last GPHY
firmware is loaded to not slow down the initialization too much (
xRX200 has two GPHYs but newer SoCs have at least three GPHYs).
Fixes: 14fceff4771e51 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20201115165757.552641-1-martin.blumenstingl@googlemail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 92307069a96c07d9b6e74b96b79390e7cd7d2111 ]
As soon as you add the second port to a VLAN, all other port
membership configuration is overwritten with zeroes. The HW interprets
this as all ports being "unmodified members" of the VLAN.
In the simple case when all ports belong to the same VLAN, switching
will still work. But using multiple VLANs or trying to set multiple
ports as tagged members will not work.
On the 6352, doing a VTU GetNext op, followed by an STU GetNext op
will leave you with both the member- and state- data in the VTU/STU
data registers. But on the 6097 (which uses the same implementation),
the STU GetNext will override the information gathered from the VTU
GetNext.
Separate the two stages, parsing the result of the VTU GetNext before
doing the STU GetNext.
We opt to update the existing implementation for all applicable chips,
as opposed to creating a separate callback for 6097, because although
the previous implementation did work for (at least) 6352, the
datasheet does not mention the masking behavior.
Fixes: ef6fcea37f01 ("net: dsa: mv88e6xxx: get STU entry on VTU GetNext")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Link: https://lore.kernel.org/r/20201112114335.27371-1-tobias@waldekranz.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a7920efdd86d8a0d74402dbc80ead03b023294ba ]
There is an off-by-one error in rtl8366rb_is_vlan_valid()
making VLANs 0..4094 valid while it should be 1..4095.
Fix it.
Fixes: d8652956cf37 ("net: dsa: realtek-smi: Add Realtek SMI driver")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3dfe8dde093a07e82fa472c0f8c29a7f6a2006a5 ]
We go to lengths to determine whether the PVID should be set
for this port or not, and then fail to take it into account.
Fix this oversight.
Fixes: d8652956cf37 ("net: dsa: realtek-smi: Add Realtek SMI driver")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7e1301ed1881447d2a25f9c6423738c33cbca133 ]
The VLANs and PVIDs on the RTL8366 utilizes a "member
configuration" (MC) which is largely unexplained in the
code.
This set-up requires a special ordering: rtl8366_set_pvid()
must be called first, followed by rtl8366_set_vlan(),
else the MC will not be properly allocated. Relax this
by factoring out the code obtaining an MC and reuse
the helper in both rtl8366_set_pvid() and
rtl8366_set_vlan() so we remove this strict ordering
requirement.
In the process, add some better comments and debug prints
so people who read the code understand what is going on.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6641a2c42b0a307b7638d10e5d4b90debc61389d ]
The rtl8366_set_vlan() and rtl8366_set_pvid() get invalid
VLANs tossed at it, especially VLAN0, something the hardware
and driver cannot handle. Check validity and bail out like
we do in the other callbacks.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ddcaf1ebb5e4e99240f29d531ee69d4244fe416 ]
When removing a port from a VLAN we are just erasing the
member config for the VLAN, which is wrong: other ports
can be using it.
Just mask off the port and only zero out the rest of the
member config once ports using of the VLAN are removed
from it.
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Fixes: d8652956cf37 ("net: dsa: realtek-smi: Add Realtek SMI driver")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit d55dad8b1d893fae0c4e778abf2ace048bcbad86.
Upstream commit af199a1a9cb0 ("net: dsa: microchip: set the correct
number of ports") seems to have been applied twice on top of the 5.4
branch. This revert the second instance of said commit.
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 774d977abfd024e6f73484544b9abe5a5cd62de7 ]
clang static analysis reports this problem
b53_common.c:1583:13: warning: The left expression of the compound
assignment is an uninitialized value. The computed value will
also be garbage
ent.port &= ~BIT(port);
~~~~~~~~ ^
ent is set by a successful call to b53_arl_read(). Unsuccessful
calls are caught by an switch statement handling specific returns.
b32_arl_read() calls b53_arl_op_wait() which fails with the
unhandled -ETIMEDOUT.
So add -ETIMEDOUT to the switch statement. Because
b53_arl_op_wait() already prints out a message, do not add another
one.
Fixes: 1da6df85c6fb ("net: dsa: b53: Implement ARL add/del/dump operations")
Signed-off-by: Tom Rix <trix@redhat.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 788abc6d9d278ed6fa1fa94db2098481a04152b7 ]
Alter the rtl8366_vlan_add() to call rtl8366_set_vlan()
inside the loop that goes over all VIDs since we now
properly support calling that function more than once.
Augment the loop to postincrement as this is more
intuitive.
The loop moved past the last VID but called
rtl8366_set_vlan() with the port number instead of
the VID, assuming a 1-to-1 correspondence between
ports and VIDs. This was also a bug.
Cc: DENG Qingfang <dqfext@gmail.com>
Cc: Mauri Sandberg <sandberg@mailfence.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Fixes: d8652956cf37 ("net: dsa: realtek-smi: Add Realtek SMI driver")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 15ab7906cc9290afb006df1bb1074907fbcc7061 ]
The RTL8366 would not handle adding new members (ports) to
a VLAN: the code assumed that ->port_vlan_add() was only
called once for a single port. When intializing the
switch with .configure_vlan_while_not_filtering set to
true, the function is called numerous times for adding
all ports to VLAN1, which was something the code could
not handle.
Alter rtl8366_set_vlan() to just |= new members and
untagged flags to 4k and MC VLAN table entries alike.
This makes it possible to just add new ports to a
VLAN.
Put in some helpful debug code that can be used to find
any further bugs here.
Cc: DENG Qingfang <dqfext@gmail.com>
Cc: Mauri Sandberg <sandberg@mailfence.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Fixes: d8652956cf37 ("net: dsa: realtek-smi: Add Realtek SMI driver")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0f3c66a3c7b4e8b9f654b3c998e9674376a51b0f ]
The MV88E6097 chip does not support configuring jumbo frames. Prior to
commit 5f4366660d65 only the 6352, 6351, 6165 and 6320 chips configured
jumbo mode. The refactor accidentally added the function for the 6097.
Remove the erroneous function pointer assignment.
Fixes: 5f4366660d65 ("net: dsa: mv88e6xxx: Refactor setting of jumbo frames")
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3506b2f42dff66ea6814c3dfa1988bafb79e6f88 ]
When doing "ip link set dev ... up" for a ksz9477 backed link,
ksz9477_phy_setup is called and it calls phy_remove_link_mode to remove
1000baseT HDX. During phy_remove_link_mode, phy_advertise_supported is
called. Doing so reverts any previous change to advertised link modes
e.g. using a udevd .link file.
phy_remove_link_mode is not meant to be used while opening a link and
should be called during phy probe when the link is not yet available to
userspace.
Therefore move the phy_remove_link_mode calls into
ksz9477_switch_register. It indirectly calls dsa_register_switch, which
creates the relevant struct phy_devices and we update the link modes
right after that. At that time dev->features is already initialized by
ksz9477_switch_detect.
Remove phy_setup from ksz_dev_ops as no users remain.
Link: https://lore.kernel.org/netdev/20200715192722.GD1256692@lunn.ch/
Fixes: 42fc6a4c613019 ("net: dsa: microchip: prepare PHY for proper advertisement")
Signed-off-by: Helmut Grohne <helmut.grohne@intenta.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit af199a1a9cb02ec0194804bd46c174b6db262075 ]
The number of ports is incorrectly set to the maximum available for a DSA
switch. Even if the extra ports are not used, this causes some functions
to be called later, like port_disable() and port_stp_state_set(). If the
driver doesn't check the port index, it will end up modifying unknown
registers.
Fixes: b987e98e50ab ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit af199a1a9cb02ec0194804bd46c174b6db262075 ]
The number of ports is incorrectly set to the maximum available for a DSA
switch. Even if the extra ports are not used, this causes some functions
to be called later, like port_disable() and port_stp_state_set(). If the
driver doesn't check the port index, it will end up modifying unknown
registers.
Fixes: b987e98e50ab ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4d3da2d8d91f66988a829a18a0ce59945e8ae4fb ]
While trying to use the lantiq_gswip driver on one of my boards I made
a mistake when specifying the phy-mode (because the out-of-tree driver
wants phy-mode "gmii" or "mii" for the internal PHYs). In this case the
following error is printed multiple times:
Unsupported interface: 3
While it gives at least a hint at what may be wrong it is not very user
friendly. Print the human readable phy-mode and also which port is
configured incorrectly (this hardware supports ports 0..6) to improve
the cases where someone made a mistake.
Fixes: 14fceff4771e51 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 38152ea37d8bdaffa22603e0a5b5b86cfa8714c9 upstream.
Currently, setting a bridge's self PVID to other value and deleting
the default VID 1 renders untagged ports of that VLAN unable to talk to
the CPU port:
bridge vlan add dev br0 vid 2 pvid untagged self
bridge vlan del dev br0 vid 1 self
bridge vlan add dev sw0p0 vid 2 pvid untagged
bridge vlan del dev sw0p0 vid 1
# br0 cannot send untagged frames out of sw0p0 anymore
That is because the CPU port is set to security mode and its PVID is
still 1, and untagged frames are dropped due to VLAN member violation.
Set the CPU port to fallback mode so untagged frames can pass through.
Fixes: 83163f7dca56 ("net: dsa: mediatek: add VLAN support for MT7530")
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5e5502e012b8129e11be616acb0f9c34bc8f8adb ]
When a client moves from a DSA user port to a software port in a bridge,
it cannot reach any other clients that connected to the DSA user ports.
That is because SA learning on the CPU port is disabled, so the switch
ignores the client's frames from the CPU port and still thinks it is at
the user port.
Fix it by enabling SA learning on the CPU port.
To prevent the switch from learning from flooding frames from the CPU
port, set skb->offload_fwd_mark to 1 for unicast and broadcast frames,
and let the switch flood them instead of trapping to the CPU port.
Multicast frames still need to be trapped to the CPU port for snooping,
so set the SA_DIS bit of the MTK tag to 1 when transmitting those frames
to disable SA learning.
Fixes: b8f126a8d543 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3047211ca11bf77b3ecbce045c0aa544d934b945 ]
There is a soft dependency against dsa_loop_bdinfo.ko which sets up the
MDIO device registration, since there are no symbols referenced by
dsa_loop.ko, there is no automatic loading of dsa_loop_bdinfo.ko which
is needed.
Fixes: 98cd1552ea27 ("net: dsa: Mock-up driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 64fec9493f7dc9bdd7233bcfe98985c45bd0e3c1 ]
Flip the IVL_SVL_SELECT bit correctly based on the VLAN enable status,
the default is to perform Shared VLAN learning instead of Individual
learning.
Fixes: 1da6df85c6fb ("net: dsa: b53: Implement ARL add/del/dump operations")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6344dbde6a27d10d16246d734b968f84887841e2 ]
When asking the ARL to read a MAC address, we will get a number of bins
returned in a single read. Out of those bins, there can essentially be 3
states:
- all bins are full, we have no space left, and we can either replace an
existing address or return that full condition
- the MAC address was found, then we need to return its bin index and
modify that one, and only that one
- the MAC address was not found and we have a least one bin free, we use
that bin index location then
The code would unfortunately fail on all counts.
Fixes: 1da6df85c6fb ("net: dsa: b53: Implement ARL add/del/dump operations")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c2e77a18a7ed65eb48f6e389b6a59a0fd753646a ]
The ARL {MAC,VID} tuple and the forward entry were off by 0x10 bytes,
which means that when we read/wrote from/to ARL bin index 0, we were
actually accessing the ARLA_RWCTRL register.
Fixes: 1da6df85c6fb ("net: dsa: b53: Implement ARL add/del/dump operations")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit eab167f4851a19c514469dfa81147f77e17b5b20 ]
When support for the MDB entries was added, the valid bit was correctly
changed to be assigned depending on the remaining port bitmask, that is,
if there were no more ports added to the entry's port bitmask, the entry
now becomes invalid. There was another assignment a few lines below that
would override this which would invalidate entries even when there were
still multiple ports left in the MDB entry.
Fixes: 5d65b64a3d97 ("net: dsa: b53: Add support for MDB")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2e97b0cd1651a270f3a3fcf42115c51f3284c049 ]
When VLAN is enabled, and an ARL search is issued, we also need to
compare the full {MAC,VID} tuple before returning a successful search
result.
Fixes: 1da6df85c6fb ("net: dsa: b53: Implement ARL add/del/dump operations")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d0802dc411f469569a537283b6f3833af47aece9 upstream.
Commit f949a12fd697 ("net: dsa: bcm_sf2: fix buffer overflow doing
set_rxnfc") tried to fix the some user controlled buffer overflows in
bcm_sf2_cfp_rule_set() and bcm_sf2_cfp_rule_del() but the fix was using
CFP_NUM_RULES, which while it is correct not to overflow the bitmaps, is
not representative of what the device actually supports. Correct that by
using bcm_sf2_cfp_rule_size() instead.
The latter subtracts the number of rules by 1, so change the checks from
greater than or equal to greater than accordingly.
Fixes: f949a12fd697 ("net: dsa: bcm_sf2: fix buffer overflow doing set_rxnfc")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 84d2f7b708c374a15a2abe092a74e0e47d018286 ]
Moving mt7623 logic out off mt7530, is required to make hardware setting
consistent after we introduce phylink to mtk driver.
Fixes: ca366d6c889b ("net: dsa: mt7530: Convert to PHYLINK API")
Reviewed-by: Sean Wang <sean.wang@mediatek.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: René van Dorst <opensource@vdorst.com>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e045124e93995fe01e42ed530003ddba5d55db4f ]
In VLAN-unaware mode, the Egress Tag (EG_TAG) field in Port VLAN
Control register must be set to Consistent to let tagged frames pass
through as is, otherwise their tags will be stripped.
Fixes: 83163f7dca56 ("net: dsa: mediatek: add VLAN support for MT7530")
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: René van Dorst <opensource@vdorst.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pali Rohár