[ Upstream commit 6ad98e8aeb0106f453bb154933e8355849244990 ]
[Why]
There is a window of time where we optimize bandwidth due to no streams
enabled will enable PSTATE changing but HUBPs are not disabled yet.
This results in underflow counter increasing in some hotplug scenarios.
[How]
Set the optimize-bandwidth flag for later processing once all the HUBPs
are properly disabled.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b0075d114c33580f5c9fa9cee8e13d06db41471b ]
[WHY & HOW]
Using values provided by DF for latency may cause hangs in
multi display configurations. Revert change to previous value.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Haonan Wang <Haonan.Wang2@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 44a09e3d95bd2b7b0c224100f78f335859c4e193 ]
[Why]
If the BIOS table is invalid or corrupt then get_i2c_info can fail
and we dereference a NULL pointer.
[How]
Check that ddc_pin is not NULL before using it and log an error if it
is because this is unexpected.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Anson Jacob <anson.jacob@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 688f97ed3f5e339c0c2c09d9ee7ff23d5807b0a7 upstream.
When run igt@kms_vrr in a device that uses DCN2.1 architecture, we
noticed multiple failures. Furthermore, when we tested a VRR demo, we
noticed a system hang where the mouse pointer still works, but the
entire system freezes; in this case, we don't see any dmesg warning or
failure messages kernel. This happens due to a lack of vupdate_no_lock
interrupt, making the userspace wait eternally to get the event back.
For fixing this issue, we need to add the vupdate_no_lock interrupt in
the interrupt list.
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit efa18405baa55a864c61d2f3cc6fe4d363818eb3 ]
This fixes corrupted display output in HDMI deep color
10/12 bpc mode at least as observed on AMD Mullins, DCE-8.3.
It will hopefully also provide fixes for other DCE's up to
DCE-11, assuming those will need similar fixes, but i could
not test that for HDMI due to lack of suitable hw, so viewer
discretion is advised.
dce110_stream_encoder_hdmi_set_stream_attribute() is used for
HDMI setup on all DCE's and is missing color_depth assignment.
dce110_program_pix_clk() is used for pixel clock setup on HDMI
for DCE 6-11, and is missing color_depth assignment.
Additionally some of the underlying Atombios specific encoder
and pixelclock setup functions are missing code which is in
the classic amdgpu kms modesetting path and the in the radeon
kms driver for DCE6/DCE8.
encoder_control_digx_v3() - Was missing setup code wrt. amdgpu
and radeon kms classic drivers. Added here, but untested due to
lack of suitable test hw.
encoder_control_digx_v4() - Added missing setup code.
Successfully tested on AMD mullins / DCE-8.3 with HDMI deep color
output at 10 bpc and 12 bpc.
Note that encoder_control_digx_v5() has proper setup code in place
and is used, e.g., by DCE-11.2, but this code wasn't used for deep
color setup due to the missing cntl.color_depth setup in the calling
function for HDMI.
set_pixel_clock_v5() - Missing setup code wrt. classic amdgpu/radeon
kms. Added here, but untested due to lack of hw.
set_pixel_clock_v6() - Missing setup code added. Successfully tested
on AMD mullins DCE-8.3. This fixes corrupted display output at HDMI
deep color output with 10 bpc or 12 bpc.
Fixes: 4562236b3bc0 ("drm/amd/dc: Add dc display driver (v2)")
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1916866dfa4aaceba1a70db83fde569387649d93 ]
In set_clamp(), the comments and definitions for the COLOR_DEPTH_101010
and COLOR_DEPTH_121212 cases directly contradict the code comment which
explains how this should work, whereas the COLOR_DEPTH_888 case
is consistent with the code comments. Comment says the bitmask should
be chosen to align to the top-most 10 or 12 MSB's on a 14 bit bus, but
the implementation contradicts that: 10 bit case sets a mask for 12 bpc
clamping, whereas 12 bit case sets a mask for 14 bpc clamping.
Note that during my limited testing on DCE-8.3 (HDMI deep color)
and DCE-11.2 (DP deep color), this didn't have any obvious ill
effects, neither did fixing it change anything obvious for the
better, so this fix may be inconsequential on DCE, and just
reduce the confusion of innocent bystanders when reading the code
and trying to investigate problems with 10 bpc+ output.
Fixes: 4562236b3bc0 ("drm/amd/dc: Add dc display driver (v2)")
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1622711beebe887e4f0f8237fea1f09bb48e9a51 ]
[WHY]
When enabling HDMI on ComboPHY, there are not
enough clock sources to complete display detection.
[HOW]
Initialize more clock sources.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4716a7c50c5c66d6ddc42401e1e0ba13b492e105 ]
Why:
Function decide_dp_link_settings() loops infinitely when required bandwidth
can't be supported.
How:
Check the required bandwidth against verified_link_cap before trying to
find a link setting for it.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Bing Guo <bing.guo@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <anson.jacob@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 901c1ec05ef277ce9d43cb806a225b28b3efe89a ]
[WHY]
dram clock change latencies get updated using ddr4 latency table, but
does that update does not happen before validation. This value
should not be the default and should be number received from
df for better mode support.
This may cause a PState hang on high refresh panels with short vblanks
such as on 1080p 360hz or 300hz panels.
[HOW]
Update latency from 23.84 to 11.72.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 80089dd8410f356d5104496d5ab71a66a4f4646b ]
[Why]
At very high pixel clock, bandwidth calculation exceeds 32 bit size
and overflow value. This causes the resulting selection of link rate
to be inaccurate.
[How]
Change order of operation and use fixed point to deal with integer
accuracy. Also address bug found when forcing link rate.
Signed-off-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a110f3750bf8b93764f13bd1402c7cba03d15d61 ]
core_link_write_dpcd() returns enum dc_status, not ddc_result:
display/dc/core/dc_link_dp.c: In function 'dp_set_panel_mode':
display/dc/core/dc_link_dp.c:4237:11: warning: implicit conversion from 'enum dc_status' to 'enum ddc_result'
[-Wenum-conversion]
Avoid the warning by using the correct enum in the caller.
Fixes: 0b226322434c ("drm/amd/display: Synchronous DisplayPort Link Training")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7e0b367db85ef7b91399006253759a024eab7653 ]
[Why]
While booting into OS, driver updates DPP/DISP CLKs.
But init clock value is zero which is invalid.
[How]
Get current clocks value to update init clocks.
To avoid underflow.
Signed-off-by: Brandon Syu <Brandon.Syu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 728321e53045d2668bf2b8627a8d61bc2c480d3b upstream.
If we have more than 4 displays we will run
into dummy irq calls or flip timout issues.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 920bb38c518408fa2600eaefa0af9e82cf48f166 upstream.
Currently both error code paths handled in dal_gpio_open_ex() issues
ASSERT_CRITICAL(), and this leads to a kernel panic unnecessarily if
CONFIG_KGDB is enabled. Since basically both are non-critical errors
and can be recovered, drop those assert calls and use a safer one,
BREAK_TO_DEBUGGER(), for allowing the debugging, instead.
BugLink: https://bugzilla.opensuse.org/show_bug.cgi?id=1177973
Cc: <stable@vger.kernel.org>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8b7dc1fe1a5c1093551f6cd7dfbb941bd9081c2e upstream.
ASSERT_CRITICAL() invokes kgdb_breakpoint() whenever either
CONFIG_KGDB or CONFIG_HAVE_KGDB is set. This, however, may lead to a
kernel panic when no kdb stuff is attached, since the
kgdb_breakpoint() call issues INT3. It's nothing but a surprise for
normal end-users.
For avoiding the pitfall, make the kgdb_breakpoint() call only when
CONFIG_DEBUG_KERNEL_DC is set.
https://bugzilla.opensuse.org/show_bug.cgi?id=1177973
Cc: <stable@vger.kernel.org>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 37b7cb10f07c1174522faafc1d51c6591b1501d4 upstream.
[WHY]
When disabling DP video, the current REG_WAIT timeout
of 50ms is too low for certain cases with very high
VSYNC intervals.
[HOW]
Increase the timeout to 102ms, so that
refresh rates as low as 10Hz can be handled properly.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 95d620adb48f7728e67d82f56f756e8d451cf8d2 ]
[Why]
Currently mode validation is bypassed if remote sink exists. That
leads to mode set issue when a BW bottle neck exists in the link path,
e.g., a DP-to-HDMI converter that only supports HDMI 1.4.
Any invalid mode passed to Linux user space will cause the modeset
failure due to limitation of Linux user space implementation.
[How]
Mode validation is skipped only if in edid override. For real remote
sink, clock limit check should be done for HDMI remote sink.
Have HDMI related remote sink going through mode validation to
elimiate modes which pixel clock exceeds BW limitation.
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c4790a8894232f39c25c7c546c06efe074e63384 ]
[why]
Recent characterization shows increased stutter latencies on some SKUs,
leading to underflow.
[how]
Update SOC params to account for this worst case latency.
Signed-off-by: Jun Lei <jun.lei@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df8e34ac27e8a0d8dce364628226c5619693c3fd ]
[why]
When combining two or more pipes in DSC mode, there will always be more
than 1 slice per line. In this case, as per DSC rules, the sink device
is expecting that the ICH is reset at the end of each slice line (i.e.
ICH_RESET_AT_END_OF_LINE must be configured based on the number of
slices at the output of ODM). It is recommended that software set
ICH_RESET_AT_END_OF_LINE = 0xF for each DSC in the ODM combine. However
the current code only set ICH_RESET_AT_END_OF_LINE = 0xF when number of
slice per DSC engine is greater than 1 instead of number of slice per
output after ODM combine.
[how]
Add is_odm in dsc config. Set ICH_RESET_AT_END_OF_LINE = 0xF if either
is_odm or number of slice per DSC engine is greater than 1.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 85e148fb963d27152a14e6d399a47aed9bc99c15 ]
[Why]
these registers should have been double buffered. SW workaround we will have SW program the more aggressive (lower) values
whenever we are upating this register, so we will not have underflow at expense of less optimzal request pattern.
[How]
there is a driver bug where we don't check for 0, which is uninitialzed HW default. since 0 is smaller than any value we need to program,
driver end up with not programming these registers
Signed-off-by: Tony Cheng <tony.cheng@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b6adc57cff616da18ff8cff028d2ddf585c97334 ]
For DSC MST, sometimes monitors would break out
in full-screen static. The issue traced back to the
PPS generation code, where these variables were being used
uninitialized and were picking up garbage.
memset to 0 to avoid this
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: David Francis <David.Francis@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6bd0a112ec129615d23aa5d8d3dd0be0243989aa ]
[WHY]
When changing DPP global ref clock, DTO adjustments must take effect
immediately, or else underflow may occur.
It appears the original decision to double-buffer DTO adjustments was made to
prevent underflows that occur when raising DPP ref clock (which is not
double-buffered), but that same decision causes similar issues when
lowering DPP global ref clock. The better solution is to order the
adjustments according to whether clocks are being raised or lowered.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 168f09cdadbd547c2b202246ef9a8183da725f13 ]
[Why]
These aren't stable on some platform configurations when driving
multiple displays, especially on higher resolution.
In particular the delay in asserting p-state and validating from
x86 outweights any power or performance benefit from the hardware
composition.
Under some configurations this will manifest itself as extreme stutter
or unresponsiveness especially when combined with cursor movement.
[How]
Disable these for now. Exposing overlays to userspace doesn't guarantee
that they'll be able to use them in any and all configurations and it's
part of the DRM contract to have userspace gracefully handle validation
failures when they occur.
Valdiation occurs as part of DC and this in particular affects RV, so
disable this in dcn10_global_validation.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit abba907c7a20032c2d504fd5afe3af7d440a09d0 ]
[Why]
Using FRAME_UPDATE will result in infopacket to be potentially updated
one frame late.
In commit stream scenarios for previously active stream, some stale
infopacket data from previous config might be erroneously sent out on
initial frame after stream is re-enabled.
[How]
Switch to using IMMEDIATE_UPDATE mode
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Ashley Thomas <Ashley.Thomas2@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f41ed88cbd6f025f7a683a11a74f901555fba11c upstream.
GFP_KERNEL may and will sleep, and this is being executed in
a non-preemptible context; this will mess things up since it's
called inbetween DC_FP_START/END, and rescheduling will result
in the DC_FP_END later being called in a different context (or
just crashing if any floating point/vector registers/instructions
are used after the call is resumed in a different context).
Signed-off-by: Daniel Kolesa <daniel@octaforge.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8b0379a85762b516c7b46aed7dbf2a4947c00564 upstream.
[Why]
ramp_up_dispclk_with_dpp is to change dispclk, dppclk and dprefclk
according to bandwidth requirement. call stack: rv1_update_clocks -->
update_clocks --> dcn10_prepare_bandwidth / dcn10_optimize_bandwidth
--> prepare_bandwidth / optimize_bandwidth. before change dcn hw,
prepare_bandwidth will be called first to allow enough clock,
watermark for change, after end of dcn hw change, optimize_bandwidth
is executed to lower clock to save power for new dcn hw settings.
below is sequence of commit_planes_for_stream:
step 1: prepare_bandwidth - raise clock to have enough bandwidth
step 2: lock_doublebuffer_enable
step 3: pipe_control_lock(true) - make dchubp register change will
not take effect right way
step 4: apply_ctx_for_surface - program dchubp
step 5: pipe_control_lock(false) - dchubp register change take effect
step 6: optimize_bandwidth --> dc_post_update_surfaces_to_stream
for full_date, optimize clock to save power
at end of step 1, dcn clocks (dprefclk, dispclk, dppclk) may be
changed for new dchubp configuration. but real dcn hub dchubps are
still running with old configuration until end of step 5. this need
clocks settings at step 1 should not less than that before step 1.
this is checked by two conditions: 1. if (should_set_clock(safe_to_lower
, new_clocks->dispclk_khz, clk_mgr_base->clks.dispclk_khz) ||
new_clocks->dispclk_khz == clk_mgr_base->clks.dispclk_khz)
2. request_dpp_div = new_clocks->dispclk_khz > new_clocks->dppclk_khz
the second condition is based on new dchubp configuration. dppclk
for new dchubp may be different from dppclk before step 1.
for example, before step 1, dchubps are as below:
pipe 0: recout=(0,40,1920,980) viewport=(0,0,1920,979)
pipe 1: recout=(0,0,1920,1080) viewport=(0,0,1920,1080)
for dppclk for pipe0 need dppclk = dispclk
new dchubp pipe split configuration:
pipe 0: recout=(0,0,960,1080) viewport=(0,0,960,1080)
pipe 1: recout=(960,0,960,1080) viewport=(960,0,960,1080)
dppclk only needs dppclk = dispclk /2.
dispclk, dppclk are not lock by otg master lock. they take effect
after step 1. during this transition, dispclk are the same, but
dppclk is changed to half of previous clock for old dchubp
configuration between step 1 and step 6. This may cause p-state
warning intermittently.
[How]
for new_clocks->dispclk_khz == clk_mgr_base->clks.dispclk_khz, we
need make sure dppclk are not changed to less between step 1 and 6.
for new_clocks->dispclk_khz > clk_mgr_base->clks.dispclk_khz,
new display clock is raised, but we do not know ratio of
new_clocks->dispclk_khz and clk_mgr_base->clks.dispclk_khz,
new_clocks->dispclk_khz /2 does not guarantee equal or higher than
old dppclk. we could ignore power saving different between
dppclk = displck and dppclk = dispclk / 2 between step 1 and step 6.
as long as safe_to_lower = false, set dpclk = dispclk to simplify
condition check.
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6eb3cf2e06d22b2b08e6b0ab48cb9c05a8e1a107 upstream.
[Why]
Changes that are fast don't require updating DLG parameters making
this call unnecessary. Considering this is an expensive call it should
not be done on every flip.
DML touches clocks, p-state support, DLG params and a few other DC
internal flags and these aren't expected during fast. A hang has been
reported with this change when called on every flip which suggests that
modifying these fields is not recommended behavior on fast updates.
[How]
Guard the validation to only happen if update type isn't FAST.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1191
Fixes: a24eaa5c51255b ("drm/amd/display: Revalidate bandwidth before commiting DC updates")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 34b86b75dfc90ab3d996c224314ce51772a3b351 ]
Mostly a cocci-job, but it flat out refused to remove the
declaration in drivers/gpu/drm/amd/display/dc/core/dc.c so
had to do that part manually.
@swap@
identifier TEMP;
expression A,B;
@@
- TEMP = A;
- A = B;
- B = TEMP;
+ swap(A, B);
@@
type T;
identifier swap.TEMP;
@@
(
- T TEMP;
|
- T TEMP = {...};
)
... when != TEMP
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: "David (ChunMing) Zhou" <David1.Zhou@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a24eaa5c51255b344d5a321f1eeb3205f2775498 ]
[Why]
Whenever we switch between tiled formats without also switching pixel
formats or doing anything else that recreates the DC plane state we
can run into underflow or hangs since we're not updating the
DML parameters before committing to the hardware.
[How]
If the update type is FULL then call validate_bandwidth again to update
the DML parmeters before committing the state.
This is basically just a workaround and protective measure against
update types being added DC where we could run into this issue in
the future.
We can only fully validate the state in advance before applying it to
the hardware if we recreate all the plane and stream states since
we can't modify what's currently in use.
The next step is to update DM to ensure that we're creating the plane
and stream states for whatever could potentially be a full update in
DC to pre-emptively recreate the state for DC global validation.
The workaround can stay until this has been fixed in DM.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 668a6741f809f2d15d125cfe2b39661e8f1655ea ]
[WHY]
The downspread percentage was copied over from a previous version
of the display_mode_lib spreadsheet. This value has been updated,
and the previous value is too high to allow for such modes as
4K120hz. The new value is sufficient for such modes.
[HOW]
Update the value in dcn21_resource to match the spreadsheet.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3159d41db3a04330c31ece32f8b29752fc114848 ]
Check before programming the register since it isn't present on
all IPs using this code.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b73b7f48895a6a944a76a2d8cdd7feee72bb1f0b upstream.
This reverts commit 967a3b85bac91c55eff740e61bf270c2732f48b2.
Reason for revert: Root cause of this issue is found. The workaround is not needed anymore.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9941b8129030c9202aaf39114477a0e58c0d6ffc ]
[Why]
In some scenario like 1366x768 VSR enabled connected with a 4K monitor
and playing 4K video in clone mode, underflow will be observed due to
decrease dppclk when previouse surface scan isn't finished
[How]
In this use case, surface flip is switching between 4K and 1366x768,
1366x768 needs smaller dppclk, and when decrease the clk and previous
surface scan is for 4K and scan isn't done, underflow will happen. Not
doing optimize bandwidth in case of flip pending.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3bae20137cae6c03f58f96c0bc9f3d46f0bc17d4 ]
[Why]
If a plane isn't being actively enabled or disabled then DC won't
always recalculate scaling rects and ratios for the primary plane.
This results in only a partial or corrupted rect being displayed on
the screen instead of scaling to fit the screen.
[How]
Add back the logic to recalculate the scaling rects into
dc_commit_updates_for_stream since this is the expected place to
do it in DC.
This was previously removed a few years ago to fix an underscan issue
but underscan is still functional now with this change - and it should
be, since this is only updating to the latest plane state getting passed
in.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 346d8a0a3c91888a412c2735d69daa09c00f0203 ]
[Why]
After v_total_min and max are updated in vrr structure, the changes are
not reflected in stream adjust. When these values are read from stream
adjust it does not reflect the actual state of the system.
[How]
Set stream adjust values equal to vrr adjust values after vrr adjust
values are updated.
Signed-off-by: Isabel Zhang <isabel.zhang@amd.com>
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Dmytro Laktyushkin