[ Upstream commit dcabb06bf127b3e0d3fbc94a2b65dd56c2725851 ]
UniPhier LD20 and PXs3 boards have RTL8211E ethernet phy, and the phy have
the RX/TX delays of RGMII interface using pull-ups on the RXDLY and TXDLY
pins.
After the commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e rx/tx
delay config"), the delays are working correctly, however, "rgmii" means
no delay and the phy doesn't work. So need to set the phy-mode to
"rgmii-id" to show that RX/TX delays are enabled.
Fixes: c73730ee4c9a ("arm64: dts: uniphier: add AVE ethernet node")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c8aebc1346522d3569690867ce3996642ad52e01 ]
This fixes the bindings in media framework:
The CSI40 is endpoint number 2
The CSI41 is endpoint number 3
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20210312174735.2118212-1-niklas.soderlund+renesas@ragnatech.se
Fixes: 3182aa4e0bf4d0ee ("arm64: dts: renesas: r8a77980: add CSI2/VIN support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de3abdf3d15c6e7f456e2de3f9da78f3a31414cc ]
The last cell of 'gpio-ranges' should be number of GPIO pins, and in
case of qcom platform it should match msm_pinctrl_soc_data.ngpio rather
than msm_pinctrl_soc_data.ngpio - 1.
This fixes the problem that when the last GPIO pin in the range is
configured with the following call sequence, it always fails with
-EPROBE_DEFER.
pinctrl_gpio_set_config()
pinctrl_get_device_gpio_range()
pinctrl_match_gpio_range()
Fixes: e13c6d144fa0 ("arm64: dts: qcom: sm8150: Add base dts file")
Cc: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20210303033106.549-3-shawn.guo@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1d88358a89dbac9c7d4559548b9a44840456e6fb upstream.
Add "syscon" compatible to the North Bridge clocks node to allow the
cpufreq driver to access these registers via syscon API.
This is needed for a fix of cpufreq driver.
Signed-off-by: Marek Behún <kabel@kernel.org>
Fixes: e8d66e7927b2 ("arm64: dts: marvell: armada-37xx: add nodes...")
Cc: stable@vger.kernel.org
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4d09ccc4a81e7de6b002482af554d8b5626f5041 ]
Commit 941432d00768 ("arm64: dts: allwinner: Drop non-removable from
SoPine/LTS SD card") enabled the card detect GPIO for the SOPine module,
along the way with the Pine64-LTS, which share the same base .dtsi.
This was based on the observation that the Pine64-LTS has as "push-push"
SD card socket, and that the schematic mentions the card detect GPIO.
After having received two reports about failing SD card access with that
patch, some more research and polls on that subject revealed that there
are at least two different versions of the Pine64-LTS out there:
- On some boards (including mine) the card detect pin is "stuck" at
high, regardless of an microSD card being inserted or not.
- On other boards the card-detect is working, but is active-high, by
virtue of an explicit inverter circuit, as shown in the schematic.
To cover all versions of the board out there, and don't take any chances,
let's revert the introduction of the active-low CD GPIO, but let's use
the broken-cd property for the Pine64-LTS this time. That should avoid
regressions and should work for everyone, even allowing SD card changes
now.
The SOPine card detect has proven to be working, so let's keep that
GPIO in place.
Fixes: 941432d00768 ("arm64: dts: allwinner: Drop non-removable from SoPine/LTS SD card")
Reported-by: Michael Weiser <michael.weiser@gmx.de>
Reported-by: Daniel Kulesz <kuleszdl@posteo.org>
Suggested-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Michael Weiser <michael.weiser@gmx.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210414104740.31497-1-andre.przywara@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3dd4ce4185df6798dcdcc3669bddb35899d7d5e1 ]
Commit 941432d00768 ("arm64: dts: allwinner: Drop non-removable from
SoPine/LTS SD card") enabled the card detect GPIO for the SOPine module,
along the way with the Pine64-LTS, which share the same base .dtsi.
However while both boards indeed have a working CD GPIO on PF6, the
polarity is different: the SOPine modules uses a "push-pull" socket,
which has an active-high switch, while the Pine64-LTS use the more
traditional push-push socket and the common active-low switch.
Fix the polarity in the sopine.dtsi, and overwrite it in the LTS
board .dts, to make the SD card work again on systems using SOPine
modules.
Fixes: 941432d00768 ("arm64: dts: allwinner: Drop non-removable from SoPine/LTS SD card")
Reported-by: Ashley <contact@victorianfox.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210316144219.5973-1-andre.przywara@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5cfad4f45806f6f898b63b8c77cea7452c704cb3 ]
Fix address of the pad control register
(IOMUXC_SW_PAD_CTL_PAD_SD1_DATA0) for SD1_DATA0_GPIO2_IO2. This seems
to be a typo but it leads to an exception when pinctrl is applied due to
wrong memory address access.
Signed-off-by: Oliver Stäbler <oliver.staebler@bytesatwork.ch>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Fixes: c1c9d41319c3 ("dt-bindings: imx: Add pinctrl binding doc for imx8mm")
Fixes: 748f908cc882 ("arm64: add basic DTS for i.MX8MQ")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 4fb3a074755b7737c4081cffe0ccfa08c2f2d29d upstream.
Crypto engine (CAAM) on LS1043A platform is configured HW-coherent,
mark accordingly the DT node.
Lack of "dma-coherent" property for an IP that is configured HW-coherent
can lead to problems, similar to what has been reported for LS1046A.
Cc: <stable@vger.kernel.org> # v4.8+
Fixes: 63dac35b58f4 ("arm64: dts: ls1043a: add crypto node")
Link: https://lore.kernel.org/linux-crypto/fe6faa24-d8f7-d18f-adfa-44fa0caa1598@arm.com
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ba8da03fa7dff59d9400250aebd38f94cde3cb0f upstream.
Crypto engine (CAAM) on LS1012A platform is configured HW-coherent,
mark accordingly the DT node.
Lack of "dma-coherent" property for an IP that is configured HW-coherent
can lead to problems, similar to what has been reported for LS1046A.
Cc: <stable@vger.kernel.org> # v4.12+
Fixes: 85b85c569507 ("arm64: dts: ls1012a: add crypto node")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a9d9bfcadfb43b856dbcf9419de75f7420d5a225 ]
The partition called "u-boot" in reality contains TF-A and U-Boot, and
TF-A is before U-Boot.
Rename this parition to "a53-firmware" to avoid confusion for users,
since they cannot simply build U-Boot from U-Boot repository and flash
the resulting image there. Instead they have to build the firmware with
the sources from the mox-boot-builder repository [1] and flash the
a53-firmware.bin binary there.
[1] https://gitlab.nic.cz/turris/mox-boot-builder
Signed-off-by: Marek Behún <kabel@kernel.org>
Fixes: 7109d817db2e ("arm64: dts: marvell: add DTS for Turris Mox")
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 948c657cc45e8ce48cb533d4e2106145fa765759 ]
In contrast to the H6 (and later) manuals, the A64 datasheet does not
specify any limitations in the maximum possible frequency for eMMC
controllers.
However experimentation has found that a 150 MHz limit similar to other
SoCs and also the MMC0 and MMC1 controllers on the A64 seems to exist
for the MMC2 controller.
Limit the frequency for the MMC2 controller to 150 MHz in the SoC .dtsi.
The Pinebook seems to be the an odd exception, since it apparently seems
to work with 200 MHz as well, so overwrite this in its board .dts file.
Tested on a Pine64-LTS: 200 MHz HS-200 fails, 150 MHz HS-200 works.
Fixes: 22be992faea7 ("arm64: allwinner: a64: Increase the MMC max frequency")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210113152630.28810-7-andre.przywara@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cfe6c487b9a1abc6197714ec5605716a5428cf03 ]
The H6 manual explicitly lists a frequency limit of 150 MHz for the bus
frequency of the MMC controllers. So far we had no explicit limits in the
DT, which limited eMMC to the spec defined frequencies, or whatever the
driver defines (both Linux and FreeBSD use 52 MHz here).
Put those maximum frequencies in the SoC .dtsi, to allow higher speed
modes (which still would need to be explicitly enabled, per board).
Tested with an eMMC using HS-200 on a Pine H64. Running at the spec'ed
200 MHz indeed fails with I/O errors, but 150 MHz seems to work stably.
Fixes: 8f54bd1595b3 ("arm64: allwinner: h6: add device tree nodes for MMC controllers")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210113152630.28810-6-andre.przywara@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 941432d007689f3774646e41a1439228b6c6ee0e ]
The SD card on the SoPine SoM module is somewhat concealed, so was
originally defined as "non-removable".
However there is a working card-detect pin (tested on two different
SoM versions), and in certain SoM base boards it might be actually
accessible at runtime.
Also the Pine64-LTS shares the SoPine base .dtsi, so inherited the
non-removable flag, even though the SD card slot is perfectly accessible
and usable there. (It turns out that just *my* board has a broken card
detect switch, so I originally thought CD wouldn't work on the LTS.)
Drop the "non-removable" flag to describe the SD card slot properly.
Fixes: c3904a269891 ("arm64: allwinner: a64: add DTSI file for SoPine SoM")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210113152630.28810-5-andre.przywara@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit da2fb8457f71138d455cba82edec0d34f858e506 ]
In recent Allwinner SoCs the first USB host controller (HCI0) shares
the first PHY with the MUSB controller. Probably to make this sharing
work, we were avoiding to declare this in the DT. This has two
shortcomings:
- U-Boot (which uses the same .dts) cannot use this port in host mode
without a PHY linked, so we were loosing one USB port there.
- It requires the MUSB driver to be enabled and loaded, although we
don't actually use it.
To avoid those issues, let's add this PHY link to the H6 .dtsi file.
After all PHY port 0 *is* connected to HCI0, so we should describe
it as this.
This makes it work in U-Boot, also improves compatiblity when no MUSB
driver is loaded (for instance in distribution installers).
Fixes: eabb3d424b6d ("arm64: dts: allwinner: h6: add USB2-related device nodes")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210113152630.28810-3-andre.przywara@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cc72570747e43335f4933a24dd74d5653639176a ]
In recent Allwinner SoCs the first USB host controller (HCI0) shares
the first PHY with the MUSB controller. Probably to make this sharing
work, we were avoiding to declare this in the DT. This has two
shortcomings:
- U-Boot (which uses the same .dts) cannot use this port in host mode
without a PHY linked, so we were loosing one USB port there.
- It requires the MUSB driver to be enabled and loaded, although we
don't actually use it.
To avoid those issues, let's add this PHY link to the A64 .dtsi file.
After all PHY port 0 *is* connected to HCI0, so we should describe
it as this. Remove the part from the Pinebook DTS which already had
this property.
This makes it work in U-Boot, also improves compatiblity when no MUSB
driver is loaded (for instance in distribution installers).
Fixes: dc03a047df1d ("arm64: allwinner: a64: add EHCI0/OHCI0 nodes to A64 DTSI")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210113152630.28810-2-andre.przywara@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1fea2eb2f5bbd3fbbe2513d2386b5f6e6db17fd7 ]
The Samsung PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Fixes: 9589f7721e16 ("arm64: dts: Add S2MPS15 PMIC node on exynos7-espresso")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201210212903.216728-8-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e98e2367dfb4b6d7a80c8ce795c644124eff5f36 ]
The Samsung PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Fixes: 01e5d2352152 ("arm64: dts: exynos: Add dts file for Exynos5433-based TM2 board")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20201210212903.216728-7-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1e0ca5467445bc1f41a9e403d6161a22f313dae7 upstream.
HDA initialization is failing occasionally on Tegra210 and following
print is observed in the boot log. Because of this probe() fails and
no sound card is registered.
[16.800802] tegra-hda 70030000.hda: no codecs found!
Codecs request a state change and enumeration by the controller. In
failure cases this does not seem to happen as STATETS register reads 0.
The problem seems to be related to the HDA codec dependency on SOR
power domain. If it is gated during HDA probe then the failure is
observed. Building Tegra HDA driver into kernel image avoids this
failure but does not completely address the dependency part. Fix this
problem by adding 'power-domains' DT property for Tegra210 HDA. Note
that Tegra186 and Tegra194 HDA do this already.
Fixes: 742af7e7a0a1 ("arm64: tegra: Add Tegra210 support")
Depends-on: 96d1f078ff0 ("arm64: tegra: Add SOR power-domain for Tegra210")
Cc: <stable@vger.kernel.org>
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 93f2a11580a9732c1d90f9e01a7e9facc825658f ]
The GCC_LPASS_Q6_AXI_CLK and GCC_LPASS_SWAY_CLK clocks may not be
touched on a typical UEFI based SDM845 device, but when the kernel is
built with CONFIG_SDM_LPASSCC_845 this happens, unless they are marked
as protected-clocks in the DT.
This was done for the MTP and the Pocophone, but not for DB845c and the
Lenovo Yoga C630 - causing these to fail to boot if the LPASS clock
controller is enabled (which it typically isn't).
Tested-by: Vinod Koul <vkoul@kernel.org> #on db845c
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20201222001103.3112306-1-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 43f20b1c6140896916f4e91aacc166830a7ba849 ]
It recently became apparent that the lack of a 'device_type = "pci"'
in the PCIe root complex node for rk3399 is a violation of the PCI
binding, as documented in IEEE Std 1275-1994. Changes to the kernel's
parsing of the DT made such violation fatal, as drivers cannot
probe the controller anymore.
Add the missing property makes the PCIe node compliant. While we
are at it, drop the pointless linux,pci-domain property, which only
makes sense when there are multiple host bridges.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200815125112.462652-3-maz@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aa880c6f3ee6dbd0d5ab02026a514ff8ea0a3328 ]
Dcfg was overlapping with clockgen address space which resulted
in failure in memory allocation for dcfg. According regs description
dcfg size should not be bigger than 4KB.
Signed-off-by: Zyta Szpak <zr@semihalf.com>
Fixes: 8126d88162a5 ("arm64: dts: add QorIQ LS1046A SoC support")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7386a559caa6414e74578172c2bc4e636d6bd0a0 ]
In accordance with the DWC USB3 bindings the property is supposed to have
uint32 type. It's erroneous from the DT schema and driver points of view
to declare it as boolean. As Neil suggested set it to 0x20 so not break
the platform and to make the dtbs checker happy.
Link: https://lore.kernel.org/linux-usb/20201010224121.12672-16-Sergey.Semin@baikalelectronics.ru/
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Fixes: 9baf7d6be730 ("arm64: dts: meson: g12a: Add G12A USB nodes")
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20201210091756.18057-3-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a9164910c5ceed63551280a4a0b85d37ac2b19a5 ]
Indicated by AML code in ACPI table, the touchpad in-use could be found
on two possible slave addresses on &i2c3, i.e. hid@15 and hid@2c. And
which one is in-use can be determined by reading another address on the
I2C bus. Unfortunately, for DT boot, there is currently no support in
firmware to make this check and patch DT accordingly. This results in
a non-functional touchpad on those C630 devices with hid@2c.
As i2c-hid driver will stop probing the device if there is nothing on
the slave address, we can actually keep both devices enabled in DT, and
i2c-hid driver will only probe the existing one. The only problem is
that we cannot set up pinctrl in both device nodes, as two devices with
the same pinctrl will cause pin conflict that makes the second device
fail to probe. Let's move the pinctrl state up to parent node to solve
this problem. As the pinctrl state of parent node is already defined in
sdm845.dtsi, it ends up with overwriting pinctrl-0 with i2c3_hid_active
state added in there.
Fixes: 11d0e4f28156 ("arm64: dts: qcom: c630: Polish i2c-hid devices")
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20210102045940.26874-1-shawn.guo@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1653e3d470629d25c64cd8a2f84adb20a9348b0c ]
The offset of the reset request register is 0, the absolute address is
0x1e60000. Boards without PSCI support will fail to perform a reset:
[ 26.734700] reboot: Restarting system
[ 27.743259] Unable to restart system
[ 27.746845] Reboot failed -- System halted
Fixes: 8897f3255c9c ("arm64: dts: Add support for NXP LS1028A SoC")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d07c3b3a886fefd583c1b485b5e4e3c4e2da493 ]
According to the datasheet (Rev. 1.9) the RTL8211F requires at least
72ms "for internal circuits settling time" before accessing the PHY
registers. On similar boards with the same PHY this fixes an issue where
Ethernet link would not come up when using ip link set down/up.
Fixes: ed5e8f689154 ("arm64: dts: meson: g12a: x96-max: fix the Ethernet PHY reset line")
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/12506964ca5d5f936579a280ad0a7e7f9a0a2d4c.1607363522.git.stefan@agner.ch
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c183c406c4321002fe85b345b51bc1a3a04b6d33 ]
According to the datasheet (Rev. 1.9) the RTL8211F requires at least
72ms "for internal circuits settling time" before accessing the PHY
registers. This fixes an issue seen on ODROID-C2 where the Ethernet
link doesn't come up when using ip link set down/up:
[ 6630.714855] meson8b-dwmac c9410000.ethernet eth0: Link is Down
[ 6630.785775] meson8b-dwmac c9410000.ethernet eth0: PHY [stmmac-0:00] driver [RTL8211F Gigabit Ethernet] (irq=36)
[ 6630.893071] meson8b-dwmac c9410000.ethernet: Failed to reset the dma
[ 6630.893800] meson8b-dwmac c9410000.ethernet eth0: stmmac_hw_setup: DMA engine initialization failed
[ 6630.902835] meson8b-dwmac c9410000.ethernet eth0: stmmac_open: Hw setup failed
Fixes: f29cabf240ed ("arm64: dts: meson: use the generic Ethernet PHY reset GPIO bindings")
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/4a322c198b86e4c8b3dda015560a683babea4d63.1607363522.git.stefan@agner.ch
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 94dad6bed3c86c00050bf7c2b2ad6b630facae31 ]
For UARTs, the local pull-ups should be on the RX pin, not the TX pin.
UARTs transmit active-low, so a disconnected RX pin should be pulled
high instead of left floating to prevent noise being interpreted as
transmissions.
This gets rid of bogus sysrq events when the UART console is not
connected.
Fixes: 52e02d377a72 ("arm64: dts: rockchip: add core dtsi file for RK3328 SoCs")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20201204064805.6480-1-wens@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b6c605e00ce8910d7ec3d9a54725d78b14db49b9 ]
The max frequency for the w25q32 (VIM v1.2) and w25q128 (VIM v1.4) spifc
chip should be 104Mhz not 30MHz.
Fixes: b8b74dda3908 ("ARM64: dts: meson-gxm: Add support for Khadas VIM2")
Signed-off-by: Artem Lapkin <art@khadas.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20201125024001.19036-1-christianshewitt@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11d0e4f281565ef757479764ce7fd8d35eeb01b0 ]
The numbering of the i2c busses differs from ACPI and a number of typos
was made in the original patch. Further more the irq flags for the
various resources was not correct and i2c3 only has one of the two
client devices active in any one device.
Also label the various devices, for easier comparison with the ACPI
tables.
Tested-by: Steev Klimaszewski <steev@kali.org>
Fixes: 44acee207844 ("arm64: dts: qcom: Add Lenovo Yoga C630")
Link: https://lore.kernel.org/r/20201130165924.319708-1-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d0570a575aa83116bd0f6a99c4de548af773d950 ]
On the LS1028A the ENETC reference clock is connected to 4th HWA output,
see Figure 7 "Clock subsystem block diagram".
The PHC may run with a wrong frequency. ptp_qoriq_auto_config() will read
the clock speed of the clock given in the device tree. It is likely that,
on the reference board this wasn't noticed because both clocks have the
same frequency. But this must not be always the case. Fix it.
Fixes: 49401003e260 ("arm64: dts: fsl: ls1028a: add ENETC 1588 timer node")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4076a007bd0f6171434bdb119a0b8797749b0502 ]
The board has a standard USB A female port connected to the USB OTG
controller's data pins. Set dr_mode in the OTG controller node to
indicate this usage, instead of having the implementation guess.
Fixes: 2171f4fdac06 ("arm64: dts: rockchip: add roc-rk3328-cc board")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20201126073336.30794-2-wens@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3aa669a994c9110a2dc7e08a5c0958a9ea5eb17c ]
Use property name `phy-handle` instead of the deprecated `phy` to
connect eth2 to the PHY.
Signed-off-by: Marek Behún <kabel@kernel.org>
Fixes: 7109d817db2e ("arm64: dts: marvell: add DTS for Turris Mox")
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b26c1a034885923822f6c4d94f8644d32bc2481 ]
Fix the device-tree entry that represents I/O High Voltage property
by replacing 'nvidia,io-high-voltage' with 'nvidia,io-hv' as the former
entry is deprecated.
Fixes: dbb72e2c305b ("arm64: tegra: Add configuration for PCIe C5 sideband signals")
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e1e47fbca668507a81bb388fcae044b89d112ecc ]
It's not possible to reboot or poweroff Exynos7420 using PSCI. Instead
we need to use syscon reboot/poweroff drivers, like it's done for other
Exynos SoCs. This was confirmed by checking vendor source and testing it
on Samsung Galaxy S6 device based on this SoC.
To be able to use custom restart/poweroff handlers instead of PSCI
functions, we need to correct psci compatible. This also requires us to
provide function ids for CPU_ON and CPU_OFF.
Fixes: fb026cb65247 ("arm64: dts: Add reboot node for exynos7")
Fixes: b9024cbc937d ("arm64: dts: Add initial device tree support for exynos7")
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Link: https://lore.kernel.org/r/20201107133926.37187-2-pawel.mikolaj.chmiel@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 73bc7510ea0dafb4ff1ae6808759627a8ec51f5a ]
Exynos7 uses the same syscon reboot and poweroff nodes as other Exynos
SoCs, so instead of duplicating code we can just include common dtsi
file, which already contains definitions of them. After this change,
poweroff node will be also available, previously this dts file did
contain only reboot node.
Fixes: fb026cb65247 ("arm64: dts: Add reboot node for exynos7")
Fixes: b9024cbc937d ("arm64: dts: Add initial device tree support for exynos7")
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Link: https://lore.kernel.org/r/20201107133926.37187-1-pawel.mikolaj.chmiel@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 53e573dc39fba1834f3e4fa002cb754b61a30701 ]
The CAT875 sub board from Silicon Linux uses Realtek phy and the driver
does not support rxc-skew-ps property.
Fixes: 6b170cd3ed02949f ("arm64: dts: renesas: cat875: Add ethernet support")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20201015132350.8360-2-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fb319496935b7475a863a00c76895e8bb3216704 ]
Commit ff4c371d2bc0 ("arm64: defconfig: Build ADMA and ACONNECT driver")
enable the Tegra ADMA and ACONNECT drivers and this is causing resume
from system suspend to fail on Jetson TX2. Resume is failing because the
ACONNECT driver is being resumed before the BPMP driver, and the ACONNECT
driver is attempting to power on a power-domain that is provided by the
BPMP. While a proper fix for the resume sequencing problem is identified,
disable the ACONNECT for Jetson TX2 temporarily to avoid breaking system
suspend.
Please note that ACONNECT driver is used by the Audio Processing Engine
(APE) on Tegra, but because there is no mainline support for APE on
Jetson TX2 currently, disabling the ACONNECT does not disable any useful
feature at the moment.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2013a4b684b6eb614ee5c9a3c07b0ae6f5ca96d9 ]
The scripts/dtc/checks.c requires that the node have empty "dma-ranges"
property must have the same "#address-cells" and "#size-cells" values as
the parent node. Otherwise, the following warnings is reported:
arch/arm64/boot/dts/broadcom/stingray/stingray-usb.dtsi:7.3-14: Warning \
(dma_ranges_format): /usb:dma-ranges: empty "dma-ranges" property but \
its #address-cells (1) differs from / (2)
arch/arm64/boot/dts/broadcom/stingray/stingray-usb.dtsi:7.3-14: Warning \
(dma_ranges_format): /usb:dma-ranges: empty "dma-ranges" property but \
its #size-cells (1) differs from / (2)
Arnd Bergmann figured out why it's necessary:
Also note that the #address-cells=<1> means that any device under
this bus is assumed to only support 32-bit addressing, and DMA will
have to go through a slow swiotlb in the absence of an IOMMU.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Link: https://lore.kernel.org/r/20201016090833.1892-2-thunder.leizhen@huawei.com'
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0011c6d182774fc781fb9e115ebe8baa356029ae ]
Recently introduced async probe on mmc devices can shuffle block IDs.
Pin them to fixed values to ease booting in environments where UUIDs
are not practical. Use newly introduced aliases for mmcblk devices from [1].
[1]
https://patchwork.kernel.org/patch/11747669/
Signed-off-by: Markus Reichl <m.reichl@fivetechno.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20201104162356.1251-1-m.reichl@fivetechno.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1741e18737948c140ccc4cc643e8126d95ee6e79 ]
The AON HSP node's "reg" property size 0xa0000 will overlap with other
resources. This patch fixes that wrong value with correct size 0x90000.
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Dipen Patel <dipenp@nvidia.com>
Fixes: a38570c22e9d ("arm64: tegra: Add nodes for TCU on Tegra194")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d19d2152ca055baf20339cfacbf039c2cfb8d936 ]
The datasheet for both the industrial and consumer variant of the
SoC lists a typical voltage of 0.95V for the 1.6GHz CPU operating
point.
Fixes: e85c9d0faa75 (arm64: dts: imx8mm: Add cpufreq properties)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf5abb0132193767c07c83e06f91b777d22ba495 ]
According to the i.MX8MN TRM, there is only one OTG port. The
address for OTG2 is reserved on Nano.
This patch removes the non-existent OTG2, usbphynop2, and the usbmisc2
nodes.
Fixes: 6c3debcbae47 ("arm64: dts: freescale: Add i.MX8MN dtsi support")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Kunihiko Hayashi